DS1808Z-050+T&R Maxim Integrated Products, DS1808Z-050+T&R Datasheet
DS1808Z-050+T&R
Specifications of DS1808Z-050+T&R
Related parts for DS1808Z-050+T&R
DS1808Z-050+T&R Summary of contents
Page 1
... ORDERING INFORMATION DS1808Z-050 16-Pin SOIC -40ºC to +85ºC 45kΩ DS1808Z-050/T&R 16-Pin SOIC -40ºC to +85ºC 45kΩ DESCRIPTION The DS1808 is a dual-channel, digitally controlled, log-taper potentiometer. Each potentiometer is comprised of 32 wiper terminal positions plus a mute position. The device has three accessible potentiometer terminals that include the high-side terminal (H), the low-side terminal (L), and the wiper terminal (W) ...
Page 2
DS1808 BLOCK DIAGRAM Figure 0dB H 0 60dB L 0 >90dB SDA SCL GND PIN DESCRIPTIONS V – Power Supply Terminal. This pin acts as the positive rail. The DS1808 will support positive supply CC voltages ranging ...
Page 3
A0, A1, A2 – Address Inputs. These input pins specify the address of the device when used in a multi- dropped configuration eight individual DS1808s may be addressed on a single 2-wire bus. H0, H1 – These are ...
Page 4
OPERATION The DS1808 is a dual-channel, digitally controlled, logarithmic potentiometer. Each potentiometer has three accessible terminals, which include H multiplexed to the wiper terminal block diagram of the DS1808 is shown in Figure 1. Potentiometer Characteristics The DS1808 ...
Page 5
SERIAL PROTOCOL The following bus protocol has been defined: § Data transfer may be initiated only when the bus is not busy. § During data transfer, the data line must remain stable whenever the clock line is high. Changes ...
Page 6
The master device generates all serial clock pulses and the start and stop conditions. A transfer is ended with a stop condition or with a repeated start condition. Since a repeated start condition is also the beginning of the next ...
Page 7
READING THE DS1808 As shown in Figure 4, the DS1808 provides one read command operation. This operation allows the user to read both potentiometers. To initiate a read operation, the R/W bit of the command/control byte is set to 1. ...
Page 8
Figure 3 Figure 4 Figure 5 Figure ...
Page 9
Figure ...
Page 10
TAP/ATTENUATION TABLE Figure 8 TAP POSITION ATTENUATION (dB ...
Page 11
ABSOLUTE MAXIMUM RATINGS* Voltage on All Pins (except /CE, SDA, SCL, A0, A1, and A2) Relative to Ground Voltage on Pins /CE, SDA, SCL, A0, A1, and A2 Operating Temperature Storage Temperature Soldering Temperature *This is a stress rating only ...
Page 12
ANALOG RESISTOR CHARACTERISTICS PARAMETER SYMBOL End-to-End Resistance Total Resistance Absolute Linearity Relative Linearity Interchannel Matching -3 dB Cutoff f cutoff frequency Output Noise (20Hz to 20kHz, Grounded Input, Tap = -6dB) Total Harmonic THD+N Distortion Interchannel Isolation (20Hz to 20kHz, ...
Page 13
AC ELECTRICAL CHARACTERISTICS PARAMETER SYMBOL SCL Clock Frequency Bus Free Time Between STOP and START Hold Time (repeated) t HD:STA START Condition Low Period of SCL Clock High period of SCL Clock Data Hold Time t HD:DAT Data Set-Up Time ...
Page 14
NOTES : 1. All voltages are referenced to ground. 2. I/O pins of fast mode devices must not obstruct the SDA and SCL lines The value of V should never exceed V DD either ...
Page 15
TYPICAL OPERATING CHARACTERISTICS (V = 12V -12V 5V +25ºC, unless otherwise specified ...
Page 16
TYPICAL OPERATING CHARACTERISTICS (cont 12V -12V 5V +25ºC, unless otherwise specified ...
Page 17
TYPICAL OPERATING CHARACTERISTICS (cont 12V -12V 5V +25ºC, unless otherwise specified ...