CAT5401YI-10-T2 ON Semiconductor, CAT5401YI-10-T2 Datasheet
CAT5401YI-10-T2
Specifications of CAT5401YI-10-T2
Related parts for CAT5401YI-10-T2
CAT5401YI-10-T2 Summary of contents
Page 1
CAT5401 Quad Digitally Program- mable Potentiometers (DPPt) with 64 Taps and SPI Interface Description The CAT5401 is four Digitally Programmable Potentiometers (DPPst) integrated with control logic and 16 bytes of NVRAM memory. Each DPP consists of a series of 63 ...
Page 2
MARKING DIAGRAMS (SOIC−24) L3B CAT5401WT −RRYMXXXX L = Assembly Location 3 = Lead Finish − Matte−Tin B = Product Revision (Fixed as “B”) CAT = Fixed as “CAT” 5401W = Device Code T = Temperature Range (I = Industrial) − ...
Page 3
CS SCK SI INTERFACE SO WP CONTROL Table 1. PIN DESCRIPTIONS Pin# (SOIC) Pin# (TSSOP ...
Page 4
Pin Descriptions SI: Serial Input SI is the serial data input pin. This pin is used to input all opcodes, byte addresses and data to be written to the CAT5401. Input data is latched on the rising edge of the ...
Page 5
Table 2. ABSOLUTE MAXIMUM RATINGS Parameters Temperature Under Bias Storage Temperature Voltage on Any Pin with Respect with Respect to Ground CC Package Power Dissipation Capability (T Lead Soldering Temperature (10 s) Wiper Current Stresses exceeding ...
Page 6
Table 5. D.C. OPERATING CHARACTERISTICS Symbol Parameter I Power Supply Current CC I Standby Current ( Input Leakage Current LI I Output Leakage Current LO V Input Low Voltage IL V Input High Voltage ...
Page 7
Table 9. WRITE CYCLE LIMITS Symbol t Write Cycle Time WR Table 10. RELIABILITY CHARACTERISTICS Symbol Parameter N (Note 10) Endurance END T (Note 10) Data Retention DR V (Note 10) ESD Susceptibility ZAP I (Note 10) Latch−Up LTH V ...
Page 8
Instruction and Register Description Device Type / Address Byte The first byte sent to the CAT5401 from the master/ processor is called the Device Address Byte. The most significant four bits of the Device Type address are a device type ...
Page 9
Wiper Control and Data Registers Wiper Control Register (WCR) The CAT5401 contains four 6−bit Wiper Control Registers, one for each potentiometer. The Wiper Control Register output is decoded to select one of 64 switches along its resistor array. The contents ...
Page 10
The basic sequence of the three byte instructions is illustrated in Figure 7. These three−byte instructions exchange data between the WCR and one of the Data Registers. The WCR controls the position of the wiper. The response of the wiper ...
Page 11
INC/DEC Command Issued SCK Instruction Format Table 13. READ WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESSES Table 14. WRITE WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESSES ...
Page 12
Instruction Format (continued) Table 18. GLOBAL TRANSFER DATA REGISTER (DR) TO WIPER CONTROL REGISTER (WCR) CS DEVICE ADDRESSES Table 19. GLOBAL TRANSFER WIPER CONTROL REGISTER (WCR) TO DATA REGISTER (DR) CS DEVICE ...
Page 13
PIN#1 IDENTIFICATION TOP VIEW D A SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MS-013. PACKAGE DIMENSIONS SOIC−24, 300 mils CASE 751BK−01 ISSUE O SYMBOL ...
Page 14
TOP VIEW SIDE VIEW Notes: (1) All dimensions are in millimeters. Angles in degrees. (2) Complies with JEDEC MO-153. PACKAGE DIMENSIONS TSSOP24, 4.4x7.8 CASE 948AR−01 ISSUE θ1 http://onsemi.com 14 SYMBOL MIN ...
Page 15
... CAT5401WI25 CAT5401WI10 CAT5401WI50 CAT5401WI00 CAT5401YI25 CAT5401YI10 CAT5401YI50 CAT5401YI00 12. All packages are RoHS−compliant (Lead−free, Halogen−free). 13. The standard lead finish is Matte−Tin. 14. The device used in the above example is a CAT5401WI−00−T1 (SOIC, Industrial Temperature, 100 kW, Tape & Reel, 1,000/Reel). ...