CAPACITOR, 100NF 16V X7R 1206 LOW ESL CAPACITOR, 100NF 16V X7R 1206 LOW ESL

LLL315R71C104MA11L

Manufacturer Part NumberLLL315R71C104MA11L
DescriptionCAPACITOR, 100NF 16V X7R 1206 LOW ESL CAPACITOR, 100NF 16V X7R 1206 LOW ESL
ManufacturerMurata
SeriesLLL
LLL315R71C104MA11L datasheet
 


Specifications of LLL315R71C104MA11L

Capacitance100NFVoltage Rating, Dc16V
Capacitor Dielectric TypeCERAMIC MULTI-LAYERTolerance,20%
Tolerance, -20%Temp, Op.ROHS COMPLIANT
1
Page 1
2
Page 2
3
Page 3
4
Page 4
5
Page 5
6
Page 6
7
Page 7
8
Page 8
Page 8/8

Download datasheet (127Kb)Embed
Prev
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
!Note
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
!Note
sales representatives or product engineers before ordering.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
Continued from the preceding page.
No.
Item
Appearance
No marking defects
Capacitance
Within T7.5% *1
Change
W.V.: 25V min.; 0.025 max.
D.F.
W.V.: 16V max.; 0.035 max. *1
Temperature
More than 10,000MΩ or 500Ω · F (Whichever is smaller)
14
I.R.
Cycle
Dielectric
No failure
Strength
Appearance
No marking defects
Capacitance
Humidity
Within T12.5% *1
Change
15
(Steady
State)
D.F.
0.05 max. *1
I.R.
More than 1,000MΩ or 50Ω · F (Whichever is smaller)
Appearance
No marking defects
Capacitance
Within T12.5% *1
Change
0.05 max. *1
Humidity
D.F.
16
Load
More than 500MΩ or 25Ω · F *1
I.R.
(Whichever is smaller)
Dielectric
No failure
Strength
Appearance
No marking defects
Capacitance
Within T12.5% *1
Change
High
W.V.: 25V min.; 0.04 max.
D.F.
17
Temperature
W.V.: 16V max.; 0.05 max. *1
Load
More than 1,000MΩ or 50Ω · F *1
I.R.
(Whichever is smaller)
Dielectric
No failure
Strength
*1 : The ligure Indicates typical inspection.Please refer to individual specifications.
*2 : Some of the parts are applicable in rated voltageA150%. Please refer to individual specifications.
Specifications and Test Methods
Specifications
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table. Let sit for 48T4 hours at room
temperature, then measure.
Step
Temp. (°C)
Time (min.)
• Initial measurement.
Perform a heat treatment at 150
let sit for 48T4 hours at room temperature. Perform the initial
measurement.
Sit the capacitor at 40T2°C and 90 to 95% humidity for 500T12
hours. Remove and let sit for 48T4 hours at room temperature,
then measure.
Apply the rated voltage at 40T2°C and 90 to 95% humidity for
500T12 hours. Remove and let sit for 48T4 hours at room
temperature, then measure. The charge/discharge current is
less than 50mA.
Apply 200% of the rated voltage for 1000T12 hours at the
maximum operating temperature T3°C. Let sit for 48T4 hours
at room temperature, then measure. The charge/discharge
current is less than 50mA.
•Initial measurement.
Apply 200% (*2) of the rated DC voltage for one hour at the
maximum operating temperature T3°C. Remove and let sit for
48T4 hours at room temperature.
Perform initial measurement. (*1)
C02E.pdf
05.12.14
Test Method
1
2
3
4
Min. Operating
Max. Operating
Room
Room
+0
+3
Temp.
Temp.
Temp.
Temp.
–3
–0
30T3
2 to 3
30T3
2 to 3
+0
°C for one hour and then
–10
71
12