LQ088H9DZ03 Sharp Electronics, LQ088H9DZ03 Datasheet

Page 1

...

Page 2

RECORDS OF REVISION ＭＯＤＥＬ Ｎｏ：ＬＱ０８８Ｈ９ＤＺ０３ SPEC No. Date NO. LCY-05064 Nov. 18. 2005 LCY-06036 Sep.19. 2006 B LCY-06036B Oct.16. 2006 PAGE - - 4-2) Backlight fluorescent tube driving part 4 - Used connector: BHR-02 (0.8) VS-1N Used connector: BHR-02 (8.0) ...

Page 3

This publication is the proprietary of SHARP and is copyrighted, with all rights reserved. Under the copyright laws, no part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical for any ...

Page 4

... Application This specification applies to color TFT-LCD module, LQ088H9DZ03 (2) Summary and Features This module is a color active matrix LCD module incorporating amorphous silicon TFT (Thin Film Transistor practicable in both penetration-type and reflection-type modes composed of a color TFT- LCD panel, driver ICs, control-PWB, FPC, flex rigid –PWB, frame, shielding front case, shielding back case and backlight unit Graphics and texts can be displayed on a 640× ...

Page 5

TFT-LCD panel driving part Used connector:DF9MA-31P-1V (Gilding type: Hirose Electric Co.,Ltd DF9□-31S-1V(Gilding type: Hirose Electric Co.,Ltd ) (□:A type) Table 4-1 Pin No. ...

Page 6

Backlight fluorescent tube driving part Used connector: BH R-02 (8.0) VS-1N (Gilding type: JST Co.Ltd) Fit connector: SM02 (8.0) B-BHS-1N (Gilding type: JST Co.Ltd) Table 4-2 terminal: ＣＮＡ，ＣＮＢ No. symbol ｉ/o 1 VL1 i NC ２ − VL2 i ...

Page 7

Table 6-1 Parameter +5V Supply voltage Current dissipation +10V Supply voltage Current dissipation Supply voltage −10V Current dissipation Permissive input ripple Input Low voltage Input High voltage Input current (Low) Input current (High) ◎Turn ...

Page 8

The backlight system is an edge-lighting type with double CCFT ( Cold Cathode Fluorescent Tube). The characteristics of Lamp are shown in the following table. Table 6-2 Parameter Symbol lamp voltage ＶＬ lamp current ＩＬ ＩＬＢ lamp ...

Page 9

Lamp Monitoring Interface Temperature Censor Thermistor Typ: 203 GT –1 made by Ishizuka Electronics Corporation According to the spec of the temperature sensor; B= InR1 – InR2 / (1/T1 – 1/T2) T1 absolute temperature (K) R1, R2 ...

Page 10

Characteristics of input signals Timing diagrams of input signal are shown in Fig.7-1 7-1) Timing characteristics Table 7-1 Parameter Clock frequency High time Low time Data Setup time Hold time Horizontal sync. Cycle signal Pulse width Vertical sync. Cycle ...

Page 11

Input Data Signals and Display Position on the screen D2,DH1 D1,DH1 D1,DH2 D2,DH2 D1,DH3 D1,DH240 U P D3,DH1 R G Display position of input data (H,V) LCY06036- 9 D640,DH1 B D640,DH240 ...

Page 12

Horizontal 3.3V 2.3V Sync.signal 0.9V （Hsync） 0V THp=4 ∼ (typ ． 48) ∼ 3.3V Clock 0V THc=typ ． Data signal 3.3V (R0∼5，G0∼5 Horizontal invalid data 0V B0∼5) THe 3.3V Data enable signal 0V Vertical 3.3V 2.3V Sync.signal TVp=3∼(typ．48)∼ 0.9V 0V ...

Page 13

Horizontal 3.3V 2.3V Sync.signal 0.9V 0V （Hsync） THp=4 ∼ (typ ． 48) ∼ 3.3V Clock 0V THc=typ ． Data signal 3.3V (R0∼5，G0∼5 Horizontal invalid data 0V B0∼5) THe=16clock 3.3V Data enable signal (ENAB) 0V Vertical 3.3V 2.3V Sync.signal TVp=3∼(typ．48)∼ 0.9V ...

Page 14

Input Signals, Basic Display Color and Gray Scale of Each Color Colors & Gray scale R0 R1 Gray Scale Black 0 0 − Blue − Green 0 0 − Cyan 0 0 − Red 1 ...

Page 15

Table 9-1 Parameter Symbol Viewing angle θ11/θ12/ range θ21/θ22 Contrast ratio Cr max Contrast ratio θ=0° (Perpendicular) θ=0° θ=0° θ=0° Black→White(τr) White→Black(τd) Black→L10 L10→Black Black→White(τr) White→Black(τd) Black→L10 Response time L10→Black Black→White(τr) White→Black(τd) Black→L16 L16→Black Black→White(τr) White→Black(τd) Luminance Y ...

Page 16

... Iso-contrast diagram （Ta=25℃） 100% 90% 80% 70% 60% 50% 40% 30% 20% 10 V10 ＊V0-V63≒2.2 [Reference value] Gamma curve V20 V30 V40 Gray scale Gamma curve & gamma ratio （Ta=25℃） [Reference value] Gamma 2.2 LQ088H9DZ03 V50 V60 LCY06036− 14 ...

Page 17

... V13 1.5% V14 2.2% V15 3.0% Optical characteristics measurement method (Transmissive mode) Photodetector 400mm TFT-LCD Module Fig.9-1 Optical characteristics measurement method Gamma Gray 2.2 Scale LQ088H9DZ03 0.0% V19 0.0% V23 0.1% V27 0.1% V31 0.2% V32 0.4% V35 0.6% V39 0.8% V43 1 ...

Page 18

Optical characteristics measurement method (Reflective mode) The inside surface is chemically Coated reflecting diffusely A beam (Through on optical fiber) Fig.9-2 Optical characteristics measurement method 【Note 9-1】 Viewing angle range is defined as follows. Normal line Photodetector (with luminosity correction ...

Page 19

Contrast ratio is defined as follows: Contrast ratio(CR)= ELDIM EZContrast * 【Note 9-3】Response time is obtained by measuring the transition time of photo detector output, when input signals are applied make the area "black" to ...

Page 20

Contrast ratio of reflection(CR)= 【Note 9-7】Reflective ratio is defined as follows: Reflective ratio = 【Note 9-8】 assumed that chromaticity of the light source is (x=0.313,y=0.329). The measuring system ...

Page 21

Uniformity of luminance is measured in the measurement part shown in the figure below. The measurement part is “●”symbol shown below. 15mm Uniformity of luminance ⇒ (Uniformity measurement is not included in SHARP outgoing inspection): Cpk = 1.42 ...

Page 22

Mechanical characteristics 10-1) External appearance Do not exist extreme defects. (See Fig.1) 10-2) Panel toughness Panel shall not be broken, when 19N is pressed on the center of the panel by a smooth sphere having 15mm diameter. Caution : ...

Page 23

Peel off laminator, pulling adhesive tape slowly to your side taking 5 or more second peeling off the film, pass the module to the next work process to prevent the module to get dust. discharging blower less ...

Page 24

Packing form a)Piling number of cartons : MAX 16 b)Package quantity in one carton 10 pcs c) Carton size: 318(W)×177(H)×312(D) mm d)Total mass of one carton filled with full modules: 4.4 kg e)Conditions for storage. Environment ①Temperature : 0∼40℃ ...

Page 25

Reliability Test Conditions for TFT-LCD Module Table 15-1 Remark) Temperature condition is based on operating temperature conditions on (5)-Table 5-1. No. Test items High temperature １ storage test High temperature ２ storage test Low temperature ３ storage test High ...

Page 26

...

Page 27

Fig.2 The Construction Form LCY06036-25 ...

Page 28

Fig.3 Packing Form LCY06036-26 ...