MPR24000E1002BC100 Vishay, MPR24000E1002BC100 Datasheet - Page 4

• Manufacturer Part Number: MPR24000E1002BC100
• Description: Res Thin Film 10K Ohm 0.1% 1/4W ±25ppm/°C Conformal AXL Thru-Hole Ammo Pack
• Manufacturer: Vishay
• Type: Thin Filmr

Specifications of MPR24000E1002BC100

• Resistance Value: 10 KOhm
• Tolerance: 0.1 %
• Power Rating: 1/4 W

TESTS AND REQUIREMENTS
Essentially all tests are carried out in accordance with the
following specifications:
EN 60115-1, Generic specification (includes tests)
EN 140100, Sectional specification (includes schedule for
qualification approval)
CECC 40101-806, Detail specification (includes schedule for
conformance inspection)
Most of the components are approved in accordance with the
European CECC-system, where applicable. The following
table contains only the most important tests. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068-2-xx
test method and under standard atmospheric conditions in
accordance with IEC 60068-1, 5.3. Climatic category
Document Number: 28727
Revision: 06-Oct-09
CLAUSE
60115-1
TEST PROCEDURES AND REQUIREMENTS
4.5
4.8
4.25.1
4.24
4.23
4.23.2
4.23.3
4.23.4
4.23.5
IEC
60068-2-xx
METHOD
78 (Cab)
30 (Db)
13 (M)
2 (Ba)
1 (Aa)
TEST
IEC
-
-
-
Temperature
steady state
Damp heat,
Damp heat,
Resistance
Endurance
sequence:
coefficient
Dry heat
pressure
at 70 °C
Climatic
Low air
(ΔR/R)
TEST
cyclic
Cold
High Precision Thin Film Leaded Resistors
For technical questions, contact:
Stability for product
types:
At 20/LCT/20 °C and
(40 ± 2) °C; 56 days;
90 % to 100 % RH;
U =
At 20/70/20 °C
15 °C to 35 °C
PROCEDURE
(93 ± 3) % RH
20/UCT/20 °C
70 °C; 2000 h
125 °C; 16 h
8.5 kPa; 2 h;
55 °C; 24 h;
- 55 °C; 2 h
U = U
0.5 h OFF
1.5 h ON;
1 cycle
P
70
-
max.
x R
;
or
[e-mail]
± 0.05 %; ± 0.02 %; ± 0.01 %
± 0.5 %; ± 0.25 %; ± 0.1 %;
LCT/UCT/56 (rated temperature range: Lower category
temperature, upper category temperature; damp heat, long
term, 56 days) is valid.
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
For testing the components are mounted on a test board in
accordance with IEC 60115-1, 4.31 unless otherwise
specified.
In the Test Procedures and Requirements table only the
tests and requirements are listed with reference to the
relevant clauses of IEC 60115-1 and IEC 60068-2-xx test
methods. A short description of the test procedure is also
given.
24 Ω to 100 kΩ
± 25 ppm/K; ± 15 ppm/K; ± 10 ppm/K; ± 05 ppm/K
PERMISSIBLE CHANGE (ΔR)
± (0.05 % R + 0.01 Ω)
± (0.05 % R + 0.01 Ω)
REQUIREMENTS
± 25 ppm/K
Vishay BCcomponents
± 0.5 %; ± 0.25 %; ± 0.1 %
> 100 kΩ to 1 MΩ
4.99 Ω to < 24 Ω;
www.vishay.com
MPR24
83