XC6SLX150-L1FGG900I Xilinx Inc, XC6SLX150-L1FGG900I Datasheet - Page 6

• Manufacturer Part Number: XC6SLX150-L1FGG900I
• Description: IC FPGA SPARTAN 6 147K 900FGGBGA
• Manufacturer: Xilinx Inc
• Series: Spartan® 6 LXr

Specifications of XC6SLX150-L1FGG900I

• Number Of Logic Elements/cells: 147443
• Number Of Labs/clbs: 11519
• Total Ram Bits: 4939776
• Number Of I /o: 576
• Voltage - Supply: 1.14 V ~ 1.26 V
• Mounting Type: Surface Mount
• Operating Temperature: -40°C ~ 100°C
• Package / Case: 900-BBGA
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Number Of Gates: -

Block RAM
Every Spartan-6 FPGA has between 12 and 268 dual-port block RAMs, each storing 18 Kb. Each block RAM has two
completely independent ports that share only the stored data.
Synchronous Operation
Each memory access, whether read or write, is controlled by the clock. All inputs, data, address, clock enables, and write
enables are registered. The data output is always latched, retaining data until the next operation. An optional output data
pipeline register allows higher clock rates at the cost of an extra cycle of latency.
During a write operation in dual-port mode, the data output can reflect either the previously stored data, the newly written
data, or remain unchanged.
Programmable Data Width
•
•
•
Memory Controller Block
Most Spartan-6 devices include dedicated memory controller blocks (MCBs), each targeting a single-chip DRAM (either
DDR, DDR2, DDR3, or LPDDR), and supporting access rates of up to 800 Mb/s.
The MCB has dedicated routing to predefined FPGA I/Os. If the MCB is not used, these I/Os are available as general
purpose FPGA I/Os. The memory controller offers a complete multi-port arbitrated interface to the logic inside the
Spartan-6 FPGA. Commands can be pushed, and data can be pushed to and pulled from independent built-in FIFOs, using
conventional FIFO control signals. The multi-port memory controller can be configured in many ways. An internal 32-, 64-,
or 128-bit data interface provides a simple and reliable interface to the MCB.
The MCB can be connected to 4-, 8-, or 16-bit external DRAM. The MCB, in many applications, provides a faster DRAM
interface compared to traditional internal data buses, which are wider and are clocked at a lower frequency. The FPGA logic
interface can be flexibly configured irrespective of the physical memory device. The MCB functionality is not supported in the
-3N speed grade.
Digital Signal Processing—DSP48A1 Slice
DSP applications use many binary multipliers and accumulators, best implemented in dedicated DSP slices. All
Spartan-6 FPGAs have many dedicated, full-custom, low-power DSP slices, combining high speed with small size, while
retaining system design flexibility.
Each DSP48A1 slice consists of a dedicated 18 × 18 bit two's complement multiplier and a 48-bit accumulator, both capable
of operating at up to 390 MHz. The DSP48A1 slice provides extensive pipelining and extension capabilities that enhance
speed and efficiency of many applications, even beyond digital signal processing, such as wide dynamic bus shifters,
memory address generators, wide bus multiplexers, and memory-mapped I/O register files. The accumulator can also be
used as a synchronous up/down counter. The multiplier can perform barrel shifting.
DS160 (v1.7) March 21, 2011
Preliminary Product Specification
Each port can be configured as 16K × 1, 8K × 2, 4K × 4, 2K × 9 (or 8), 1K × 18 (or 16), or 512 x 36 (or 32).
The x9, x18, and x36 configurations include parity bits. The two ports can have different aspect ratios.
Each block RAM can be divided into two completely independent 9 Kb block RAMs that can each be configured to any
aspect ratio from 8K x 1 to 512 x 18, with 256 x 36 supported in simple dual-port mode.
www.xilinx.com
Spartan-6 Family Overview
6