31-3302 Amphenol, 31-3302 Datasheet

RF Connectors BNC ST PLUG RG-59/62 210 M39012/16-0102

31-3302

Manufacturer Part Number

31-3302

Description

RF Connectors BNC ST PLUG RG-59/62 210 M39012/16-0102

Manufacturer

Amphenol

Datasheet

1.31-3301.pdf (1 pages)

Specifications of 31-3302

Product

Connector

Rf Series

BNC

Gender

Plug

Termination Style

Clamp

Body Style

Straight

Cable Type

RG 59, RG 62, RG 71, RG 140, RG 210

Connector Type

BNC Plug

Lead Free Status / Rohs Status

Lead free / RoHS Compliant

Other names

031-3302 713-1106 73K1435,

Current page: 1 of 1
Download datasheet (21Kb)

Assembly Instructions-C25

BNC

CLAMP CONNECTORS

Amphenol Corporation Tel: 800-627-7100

Step 1

Step 2

Step 3

Step 4

Step 5

For angle plugs only: (except 31-204) Solder center

conductor to preassembled contact. Assemble cap and

lightly punch center of cap for retention in body, or solder in

place.

nut

washer* gasket

* Not supplied on all items

clamp

6775

6775-75

8525

8575

9350

15875

16300

33275

69475

84975

86350

86425

86850

31-2

31-2-RFX

31-15

31-202

31-204

31-206

31-207

31-212

31-212-1005

31-850

31-3202

31-3301

31-3302

bushing‡ female contact

Amphenol

Number

‡ For use on RG-62, 71, 122, 178, 180, 196, 210

BNC Plug

BNC Angle Plug

BNC Plug

BNC Angle Plug

BNC Plug

BNC Bulkh. Jack

BNC Panel Jack

BNC Bulkh. Jack

BNC Plug

BNC Jack

BNC Plug

BNC Angle Plug

BNC Bulkhead Jack

BNC Plug

BNC Angle Plug

BNC Plug

299

Connector

BNC Plug

Type

Step 1 Place nut, washer (when supplied) and gasket over cable

Step 2 Comb out braid and fold out. Trim insulation off center

Step 3 Pull braid wires forward and taper toward center conductor.

Step 4 Fold back braid wires as shown, trim to proper length

Step 5 Insert cable and parts into connector body. Make sure

jack body

and strip jacket to dimension

conductor to dimension

71 and 210/U cable, trim an additional .032"(0.8mm) of

insulation off center conductor and add bushing.] Tin

center conductor.

Place clamp over braid and push back against cable

jacket.

[approximately .125" (3.2mm) long] and form over clamp

as shown. Braid wire should not extend beyond step of

braid clamp. Solder contact to center conductor, sliding

bushing first (when supplied) over center conductor.

sharp edge of clamp seats properly in gasket. Tighten nut

to approximately 15 inch pounds.

8, 9, 11, 213, 214

58, 141, 142, 400

59, 62, 140, 210

178, 196

180

174, 179, 187, 188, 316

122

174, 179, 187, 188, 316

178, 196

58, 141, 142, 400

58, 141, 142A

59, 62, 71, 140, 210

55, 58, 141, 142, 223, 400

58, 141, 142, 400

59, 62, 71, 140, 210

59, 62, 71, 140, 210, 302

59 (20GA CC)

59, 62, 71, 140, 210

55, 58, 141, 142, 223, 400

58, 141, 142, 223

59, 62, 71, 140, 210

male contact

RG-/U

Cable

shown in table above. [For RG-62,

shown in table above.

plug body

Amphenol

.490(12.4)

.343(8.7)

.297(7.5)

.405(10.3)

.156(3.96)

.250(6.4)

.540(13.7)

.281(7.1)

.265(6.73)

.313(7.95)

.266(6.75)

.312(7.9)

.315(8.0)

.297(7.54)

.274(6.95)

.297(7.54)

.297(7.5)

.297(7.54)

.250(6.4)

.375(9.52)

.250(6.4)

Inches (Millimeters)

www.amphenolrf.com

Stripping Dims,

.200(5.1)

.187(4.7)

.094(2.4)

.078(1.98)

.094(2.4)

.156(3.96)

.172(4.4)

.156(3.96)

.203(5.15)

.109(2.76)

.094(2.4)

.118(3.0)

.109(2.75)

.094(2.4)

.109(2.8)

.109(2.75)

.094(2.4)

.125(3.17)

.094(2.4)

Related parts for 31-3302

Related keywords

31-3302 datasheet
31-3302 data sheet
31-3302 pdf datasheet
31-3302 component
31-3302 part
31-3302 distributor
31-3302 RoHS
31-3302 datasheet download