XE8802MI035LF Semtech, XE8802MI035LF Datasheet - Page 130

• Manufacturer Part Number: XE8802MI035LF
• Description: IC DAS 16BIT FLASH 8K 100-LQFP
• Manufacturer: Semtech

Specifications of XE8802MI035LF

• Applications: Sensing Machine
• Core Processor: RISC
• Program Memory Type: FLASH (22 kB)
• Controller Series: XE8000
• Ram Size: 1K x 8
• Interface: SPI, UART
• Number Of I /o: 36
• Voltage - Supply: 2.4 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 100-LQFP
• For Use With: XE8000MP - PROG BOARD AND PROSTART2 CARD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Specifications (Cont’d)
17.8.3
17.8.3.1
The integral non-linearity depends on the selected gain configuration. First of all, the non-linearity of the ADC (all
PGA stages bypassed) is shown in Figure 17-8.
© Semtech 2006
PARAMETER
POWER SUPPLY
Voltage Supply Range, V
Analog
Consumption, Total (I
Analog Power Dissipation
TEMPERATURE
Specified Range
Operating Range
Notes:
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10) Offset error is defined as the output code error for a zero volt input (ideally, output code = 0). For ± 1 LSB offset, N
(11) INL defined as the deviation of the DC transfer curve of each individual code from the best-fit straight line. This specification holds
(12) DNL is defined as the difference (in LSB) between the ideal (1 LSB) and measured code transitions for successive codes.
(13) Figures for Gains = 1 to 100. PSRR is defined as the amount of change in the ADC output value as the power supply voltage
(14) Conversion time is given by: T
(15) PGAs are reset after each writing operation to registers RegAcCfg1-5. The ADC must be started after a PGA or inputs common-
(16) Nominal (maximum) bias currents in PGAs and ADC, i.e. IB_AMP_PGA[1:0] = ‘11’ and IB_AMP_ADC[1:0] = ‘11’.
(17) Bias currents in PGAs and ADC set to 3/4 of nominal values, i.e. IB_AMP_PGA[1:0] = ‘10’, IB_AMP_ADC[1:0] = ‘10’.
(18) Bias currents in PGAs and ADC set to 1/2 of nominal values, i.e. IB_AMP_PGA[1:0] = ‘01’, IB_AMP_ADC[1:0] = ‘01’.
(19) Bias currents in PGAs and ADC set to 1/4 of nominal values, i.e. IB_AMP_PGA[1:0] = ‘00’, IB_AMP_ADC[1:0] = ‘00’.
ADC Only
PGA1
PGA2
PGA3
Normal Power Mode
3/4 Power Reduction Mode
1/2 Power Reduction Mode
1/4 Power Reduction Mode
Gain
V
Offset due to tolerance on GDoff
Measured with block connected to inputs through AMUX block. Normalized input sampling frequency for input impedance is f
512kHz. This figure must be multiplied by 2 for f
Figure
See equation Eq. 21 to calculate equivalent input noise.
Figure independent on PGA2 gain and sampling frequency f
equivalent input noise.
Figure independent on PGA3 gain and sampling frequency f
equivalent input noise.
Resolution is given by n = 2⋅log2(OSR) + log2(N
1, 2, 4 or 8.
If a ramp signal is applied to the input, all digital codes appear in the resulting ADC output data.
Gain error is defined as the amount of deviation between the ideal (theoretical) transfer function and the measured transfer function
(with the offset error removed). (See Figure 17-19)
over the full scale.
changes.
be set to 1, 2, 4 or 8.
mode stabilisation delay. This is done by writing bit Start several cycles after PGA settings modification or channel switching.
Delay between PGA start or input channel switching and ADC start should be equivalent to OSR (between 8 and 1024) number of
cycles. This delay does not apply to conversions made without the PGAs.
IN,MAX
Linearity
Integral non-linearity
Quiescent
= ±(V
defined
independent
Q
)
REF
DD
/2)⋅(OSR/OSR+1).
as
Current
overall
from
CONV
2
or GDoff
PGA1
+2.4
MIN
-40
-40
PGA
= (N
ELCONV
XE8802 Sensing Machine Data Acquisition MCU
3
gain
gain
setting. For small intrinsic offset, use only ADC and PGA1.
720/620
250/190
165/150
130/120
175/160
VALUE
3.6/1.9
2.7/1.4
1.8/0.9
0.9/0.5
⋅ (OSR + 1) + 1) / f
TYP
+5
S
ELCONV
= 256kHz, 4 for f
GD
and
TOT
). OSR can be set between 8 and 1024, in powers of 2. N
17-18
sampling
MAX
+125
+5.5
+85
=
S
S
. See model of Figure 17-18(a). See equation Eq. 21 to calculate
. See model of Figure 17-18(a) and equation Eq. 21 to calculate
with ZoomingADC™ and LCD driver
S
GD
. OSR can be set between 8 and 1024, in powers of 2. N
S
= 128kHz. Input impedance is proportional to 1/f
1
⋅GD
UNITS
frequency
mW
mW
mW
mW
µA
µA
µA
µA
µA
°C
°C
2
V
⋅GD
3
.
COMMENTS/CONDITIONS
Only Acquisition Chain
V
V
V
V
V
All PGAs & ADC Active
V
V
V
V
Maximum
DD
DD
DD
DD
DD
DD
DD
DD
DD
f
S
.
= 5V/3V
= 5V/3V
= 5V/3V
= 5V/3V
= 5V/3V
= 5V/3V (Note 16)
= 5V/3V (Note 17)
= 5V/3V (Note 18)
= 5V/3V (Note 19)
See
input
model
voltage
of
ELCONV
Figure
www.semtech.com
ELCONV
is
S
.
can be set to
must be ≥2.
given
ELCONV
17-18(a).
can
by:
S
=