CY7C63001A-SXC Cypress Semiconductor Corp, CY7C63001A-SXC Datasheet - Page 3

• Manufacturer Part Number: CY7C63001A-SXC
• Description: IC MCU 4K USB MCU LS 20SOIC
• Manufacturer: Cypress Semiconductor Corp
• Series: M8™r

Specifications of CY7C63001A-SXC

• Applications: USB Microcontroller
• Core Processor: M8A
• Program Memory Type: OTP (4 kB)
• Controller Series: CY7C630xx
• Ram Size: 128 x 8
• Interface: USB
• Number Of I /o: 12
• Voltage - Supply: 4 V ~ 5.25 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 428-1617

4.0
5.0
6.0
The Cypress CY7C630/101A USB microcontrollers are
optimized for human-interface computer peripherals such as
a mouse, joystick, and gamepad. These USB microcontrollers
conform to the low-speed (1.5 Mbps) requirements of the USB
Specification version 1.1. Each microcontroller is a self-
contained unit with: a USB interface engine, USB transceivers,
an 8-bit RISC microcontroller, a clock oscillator, timers, and
program memory. Each microcontroller supports one USB
device address and two endpoints.
The 6-MHz clock is doubled to 12 MHz to drive the microcon-
troller. A RISC architecture with 35 instructions provides the
best balance between performance and product cost.
6.1
The memory in the USB Controller is organized into user
program memory in EPROM space and data memory in SRAM
space.
Document #: 38-08026 Rev. *A
V
V
V
XTALIN
XTALOUT
P0.0–P0.7,
P1.0–P1.7
D+, D–
CEXT
CEXT
D+
D–
V
V
V
CC
SS
PP
PP
CC
SS
Name
Name
Memory Organization
Pin Definitions
Pin Description
Functional Description
I/O
I/O
I/O
I/O
One pin. Connects to the USB power source or to a nominal 5V power supply. Actual V
between 4.0V and 5.25V.
One pin. Connects to ground.
One pin. Used in programming the on-chip EPROM. This pin should be tied to ground during normal opera-
tions.
One pin. Input from an external ceramic resonator.
One pin. Return path for the ceramic resonator (leave unconnected if driving XTALIN from an external
oscillator).
Sixteen pins. P0.0–P0.7 are the 8 I/O lines in Port 0. P1.0–P1.7 are the 8 I/O lines in Port 1. P1.0–P1.3 are
supported in the CY7C6300XA. All I/O pins include bit-programmable pull-up resistors. However, the sink
current of each pin can be programmed to one of sixteen levels. Besides functioning as GPIO lines, each
pin can be programmed as an interrupt input. The interrupt is edge-triggered, with programmable polarity.
Two pins. Bidirectional USB data lines. An external pull-up resistor must be connected between the D pin
and V
One pin. Open-drain output with Schmitt trigger input. The input is connected to a rising edge-triggered
interrupt. CEXT may be connected to an external RC to generate a wake-up from Suspend mode. See
Section 6.4.
–
–
–
CC
to select low-speed USB operation.
(continued)
20-Pin
14
13
12
9
8
7
24-pin
16
15
10
14
11
9
Die Pad #
11
16
15
10
14
9
6.1.1
The CY7C63001A and CY7C63101A each offer 4 Kbytes of
EPROM. The program memory space is divided into two
functional groups: interrupt vectors and program code.
The interrupt vectors occupy the first 16 bytes of the program
space. Each vector is 2 bytes long. After a reset, the Program
Counter points to location zero of the program space. Figure
6-1 shows the organization of the Program Memory Space.
6.1.2
The Cypress USB microcontroller includes a security fuse bit.
When the security fuse is programmed, the EPROM program
memory outputs 0xFF to the EPROM programmer, thus
protecting the user’s code.
Description
Connects to external R/C timing circuit for optional
‘suspend’ wakeup
USB data+
USB data–
Programming voltage supply, tie to ground during normal
operation
Voltage supply
Ground
Program Memory Organization
Security Fuse Bit
Description
CY7C63001A
CY7C63101A
CC
range can vary
Page 3 of 25