61F-GP-NT AC240 . Omron, 61F-GP-NT AC240 . Datasheet
61F-GP-NT AC240 .
Specifications of 61F-GP-NT AC240 .
61F-GP-NT AC240 . Summary of contents
Page 1
... Type High-sensitivity Model 8-pin 61F-GP-N8H 61F-GP-N8HY Note: When ordering, specify the desired operating voltage at the end of the model number. Example: 61F-GP-N [220 VAC] Desired supply voltage 2. Type Blank: General-purpose L 2KM: Long-distance (for 2 km) L 4KM: Long-distance (for 4 km) H: High-sensitivity D: Low-sensitivity ...
Page 2
... When the power supply voltage is applied, if there are no liquids between the electrodes (ground and operation electrodes), the internal relay will operate. If the advanced operation does not satisfy applications, consider using 61F-N8HY controller which uses sequential operation. High- Long-distance ...
Page 3
... Internal Circuit Diagrams 61F-GP-N/-NT/-NL/-ND Power supply Control circuit (See note Note: When applying a self-holding circuit, short between terminals 5 and 6 and use terminal 61F-GP-NH Power supply Control circuit (See note 61F-GP-N@ 61F-GP-NR Power supply Control circuit ...
Page 4
... Principles of Operation Pump ON Pump OFF (indicator ON) The pump starts when the water level reaches E 1 (indicator OFF). and stops when the water level drops below E 2 61F-GP-N@ Compact, Plug-in Type 61F-GP-N Dimensions: page 14 Automatic Drainage Control 61F-GP Control circuit 8 V Power supply ...
Page 5
... Electrode (the longest Electrode, terminal 4). Principles of Operation • Terminals 6 and 7, and terminals 10 and 11 on the lower -limit 61F-GP-N are shorted when the water level reaches E • Terminals 6 and 7, and terminals 10 and 11 on the intermediate 61F-GP-N are shorted when the water level reaches E • ...
Page 6
... Replacing 61F-G3N Functions (Automatic Water Supply Control with Abnormal Water Increase and Water Shortage Alarms) Connections Water shortage Commercial Voltage 61F-GP Control 0 V MCCB 24 V circuit 8 V Power supply Lower limit Alarm Contactor (See note.) Motor protection relay M P Note: The power supply phases (terminals can be matched to use the same ground for the common Electrode (the longest Electrode, terminal 4) ...
Page 7
... Note: The power supply depends on the specifications of the model. • With 2-wire connections, only two wires are required between the 61F-GP-NR and Electrode Holder, but three wires are required for the Electrodes. • The Electrode Holder must be specified for 2-wire connections. ...
Page 8
... When supplying power from N-phase to the Controller in three-phase four-line circuit, refer to the following diagrams. Line voltage (R-S, S-T, or R-T): 380 or 415 VAC Phase voltage (N-R, N-S, or N-T): 220 or 240 VAC 61F-GP-N@ 220 or 240 VAC Power source 380 or 415 VAC Source voltage: ...
Page 9
... When the power supply voltage is applied, if there are no liquids between the electrodes (ground and operation electrodes), the internal relay will operate. If the advanced operation does not satisfy applications, consider using 61F-N8HY controller which uses sequential operation. High-sensitivity Low-sensitivity ...
Page 10
... Internal Circuit Diagrams 61F-GP-N8/-N8L/-N8D/-N8HY Power supply Control circuit (see note) Note for the 61F-GP-N8HY. 61F-GP-N8Y Power supply Control circuit 61F-GP-N8H Power supply 24 V Control circuit 24 V 61F-GP-N8-V50 Power supply 24 V Control circuit 61F-GP-N@ 61F-GP-N8R Power supply Control circuit ...
Page 11
... Principles of Operation Pump ON Pump OFF (indicator ON) The pump starts when the water level reaches E 1 (indicator OFF). and stops when the water level drops below E 2 61F-GP-N@ Compact, Plug-in Type 61F-GP-N8 Dimensions: page 14 Automatic Drainage Control 61F-GP- Control circuit Power supply U 3 ...
Page 12
... Note: The power supply depends on the specifications of the model. • With 2-wire connections, only two wires are required between the 61F-GP-N8R and Electrode Holder, but three wires are required for the Electrodes. • The Electrode Holder must be specified for 2-wire connections. ...
Page 13
... When supplying power from N-phase to the Controller in three-phase four-line circuit, refer to the following diagrams. Line voltage (R-S, S-T, or R-T): 380 or 415 VAC Phase voltage (N-R, N-S, or N-T): 220 or 240 VAC 61F-GP-N8@, 220 or 240 VAC Power source 380 to 415 VAC Note: Be sure to ground terminal 1. ...
Page 14
... Dimensions Note: All units are in millimeters unless otherwise indicated. 61F-GP-N, -NT, -NL, -NH, -ND, -NR, -N -TDL, -N14, -N15, -NH3 49.4 38 61F-GP-N8, -N8L, -N8H, -N8HY, -N8D, -N8R 49.4 38 ■ Safety Precautions Refer to Safety Precautions for All Level Controllers. ALL DIMENSIONS SHOWN ARE IN MILLIMETERS. To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527. ...
Page 15
... Please read and understand this catalog before purchasing the products. Please consult your OMRON representative if you have any questions or comments. WARRANTY OMRON's exclusive warranty is that the products are free from defects in materials and workmanship for a period of one year (or other period if specified) from date of sale by OMRON. OMRON MAKES NO WARRANTY OR REPRESENTATION, EXPRESS OR IMPLIED, REGARDING NON-INFRINGEMENT, MERCHANTABILITY, OR FITNESS FOR PARTICULAR PURPOSE OF THE PRODUCTS ...