SH1B-05C IDEC Corporation, SH1B-05C Datasheet
SH1B-05C
Specifications of SH1B-05C
Related parts for SH1B-05C
SH1B-05C Summary of contents
Page 1
... With Indicator and Check Button Top Bracket Mounting With Diode (DC coil only) With Indicator and Diode (DC coil only) 1. *Carries no UL recognition mark. 2. PCB terminal relays are designed to mount directly to a circuit board without any socket. 726 RH Series Compact Power Relays Part Number Selection Part Number ...
Page 2
... USA: 800-262-IDEC Canada: 888-317-IDEC RH Series PCB Mount SH1B-62 SH2B-62 1. DIN Rail mount SH3B-62 socket comes with two horseshoe SH4B-62 clips. Do not use unless you plan to insert pullover wire spring. Replacement horseshoe clip part number is Y778-011 ...
Page 3
... M3.5 screws with captive wire clamp DIN Rail Mount SH2B-05 Sockets SH3B-05 M3.5 screws with captive wire clamp SH4B-05 (coil) M3 screws SH1B-05C (contact) M3.5 screws with captive wire clamp, fi ngersafe Finger-safe DIN Rail SH2B-05C Mount SH3B-05C M3.5 screws with captive wire clamp, fi ngersafe SH4B-05C ...
Page 4
... Measured at the rated voltage (at 20°C), excluding contact bouncing Release time of relays with diode maximum 3. Relays with indicator or diode: 1000V AC, 1 minute 4. For use under different temperature conditions, refer to Continuous Load Current vs. Operating Temperature Curve. The operating temperature range of relays with indicator or diode is –25 to +40°C. DC: 0.8W DC: 0.9W DC: 1.5W DC: 1 ...
Page 5
... AC resistive 120V AC inductive (RH3/RH4) 240V AC resistive 120V AC inductive (RH2/RH3/RH4) 10.0 AC resistive AC inductive DC resistive 50 100 200 300 www.idec.com Relays & Sockets 1000 500 30V DC resistive 100 50 100V DC resistive 30V DC inductive 20 100V DC inductive Load Current (A) 1000 30V DC resistive 500 100 30V DC ...
Page 6
... Relays & Sockets Continuous Load Current vs. Operating Temperature Curve (Basic Type, With Check Button, and Top Bracket Mounting Type) (RH1) Note: The rated voltage is applied to the coil. 100 Coil Coil Load Current (A) Internal Connection (View from Bottom) Basic Type SPDT DPDT ...
Page 7
... and over ( – – ) RH1B-U/RH1B-UL/RH1B-UD/RH1B-ULD Total length from panel surface including relay socket SH1B-05: 61.5 ( 63.5 ) max., SH1B-51: 39.6 ( 41.6 ) max. Dimensions in the ( ) include a hold-down spring. ø2.6 hole 5.4 14 35.6 max. 6.4 RH4B-U/RH4B-UL/RH4B-UD/RH4B-LD Total length from panel surface including relay socket SH4B-05: 61 ...
Page 8
... RH3V2-U/RH3V2-UL/RH3V2-D 11-ø2.4 holes 0.5 31 35.6 max. 4.6 Standard DIN Rail Mount Sockets SH1B-05 17 31.5 DIN Rail 8 18 M3.5 Terminal (BNDN) Screw 2-ø4.2 Mounting Holes (or M4 Tapped Holes) 16 5.5 min. M3 Terminal Screw 4.4 max. 16 14.5 ø3.6 min 7.9 max. ...
Page 9
... RH Series Finger-safe DIN Rail Mount Sockets SH1B-05C 17 36 M3.5 Terminal 7 25 Screw DIN Rail (BNDN) M3 Terminal Screw Ring terminals 18.7 16 cannot be used. 20 29.5 SH3B-05C 32 M3.5 Terminal 36 7 Screw DIN Rail 25 (BNDN) Ring terminals 18.7 36 cannot be used. 29.5 40 Through Panel Mount Socket ...
Page 10
... Relays & Sockets PCB Mount Sockets SH1B-62 Terminal Arrangement (Bottom View 1.5 36 min. when using 12.2 hold-down springs SH3B-62 Terminal Arrangement (Bottom View ∗ 36 min. when using 30.2 hold-down springs Dimensions con’t (mm) SH2B-62 3-ø2.4 holes 6.8 18 min. 4.4 21.2 2-ø2 holes (Tolerance 0 ...
Page 11
... Operating Instructions Driving Circuit for Relays 1. To ensure correct relay operation, apply rated voltage to the relay coil. 2. Input voltage for the DC coil: A complete DC voltage is best for the coil power to make sure of stable relay operation. When using a power supply containing a ripple voltage, suppress the ripple factor within 5%. When power is supplied through a rectifi ...
Page 12
... Add another surge absorbing provision to the relay to prevent damage. Operating Instructions con’ and CSA ratings may differ from product rated values determined by IDEC not use relays in the vicinity of strong magnetic fi eld, as this may affect relay operation. Safety Precautions Precautions for the RU Relays • ...