715P10356KD3 Vishay Specialty Capacitors, 715P10356KD3 Datasheet

715P10356KD3

Manufacturer Part Number

715P10356KD3

Description

Capacitor; 0.01 uF; 600 WVDC; + 5%; Hockey Crimped; 0.1; 400000 Megohms; -55 d

Manufacturer

Vishay Specialty Capacitors

Datasheet

1.715P22356KD3.pdf (6 pages)

Specifications of 715P10356KD3

Brand/series

ORANGE DROP® Series

Capacitance

0.01 μF

Diameter, Lead Wire

0.032 in.

Dissipation Factor

0.1 %

Insulation Resistance

400000 Megohms

Lead Pitch

0.375 ± 0.030 in.

Length

0.95 in.

Length, Lead

1.250 in. (Min.)

Material, Element

Polypropylene Film

Shelf Life

500 hr

Temperature, Operating, Maximum

105 °C

Temperature, Operating, Minimum

-55 °C

Termination

Radial

Tolerance

±5 %

Voltage, Rating

600 VDC

Lead Free Status / Rohs Status

RoHS Compliant part

Current page: 1 of 6
Download datasheet (120Kb)

Document Number: 42018

Revision 13-Nov-03

PERFORMANCE CHARACTERISTICS

Operating Temperature: - 55°C to + 85°C standard; up to

Insulation Resistance: After a 2 minute charge at rated

Capacitance, Tolerance and Dissipation Factor:

Dielectric Withstanding Voltage: Capacitors rated below

+ 105°C when working voltage is reduced to 50% of the

+ 85°C rating.

voltage or 500 V, whichever is less.

At + 25°C: 400,000 Megohm for C ≤ .5µF.

200,000 Megohm - Microfarads for C > .5 Microfarads.

At + 85°C: 20,000 Megohm for C ≤ .5 Microfarads.

10,000 Megohm - Microfarads for C > .5 Microfarads.

At + 105°C: 2000 Megohm for C ≤ .5µF.

1000 Megohm - Microfarads for C > .5 Microfarads.

Capacitors shall be measured at a frequency of 1000Hz

at + 25°C or else be referred to measurements made at

that frequency and temperature. The maximum dissipation

factor shall be 0.1%.

1000 volts shall withstand a DC potential of 250% of rated

voltage applied between terminals for not more than

5 seconds. Capacitors rated 1000 volts and above shall

withstand a DC potential of 200% of rated voltage applied

between the terminals for not more than 5 seconds. The

test voltage must be applied and discharged through a

resistor of one ohm per volt.

Polypropylene Film Capacitors

ORANGE DROP

For technical questions, contact spresale@vishay.com

Polypropylene plastic film is employed as the dielectric in Type

715P ORANGE DROP

are ideal for applications where high AC current flow is found,

r-f generators and pulse-forming networks where dielectric

heating is often a problem.

The polypropylene dielectric film is similar to polystyrene in

that it can handle high AC currents due to its low loss but with

the added advantage of an operating temperature to

+ 105°C.

Capacitance change with temperature is less than 3% over

the entire operating temperature range. The temperature

coefficient is negative and virtually linear at 180PPM/°C over

the temperature range of + 25°C to + 105°C. This characteristic

means the Type 715P is suitable for matching with positive TC

resistors and inductors to maintain circuit stability.

Type 715P ORANGE DROP

coated with a flame retardant epoxy.

Performance characteristics, as well as curves showing typical

variation in electrical characteristics as a function of temperature

and frequency, are given.

Humidity Test: Condition capacitors with no voltage

DC Life Test: Capacitors are capable of withstanding a

AC Life Test: Capacitors shall withstand the maximum

Not more than one failure allowed in 12 units tested.

applied for 72 hours at 95% relative humidity and + 75°C.

Remove capacitors from humidity chamber, wipe surface

dry of moisture and dry in circulating air for 4 hours.

Measure insulation resistance after a two minute charge at

+ 25°C and rated voltage or 500 VDC, whichever is less.

Minimum product of insulation resistance and capacitance

shall be 50,000 Megohm-microfarads after test but need

not exceed 100,000 Megohm. Not more than one failure

in 12 units tested shall be permitted.

500 hour life test at + 85°C at 150% of rated working

voltage. After test, capacitance shall not have changed by

more than 5% of initial value, insulation resistance shall

not have decreased by more than 50% of the initial limit

and dissipation factor shall not have increased to more

than 0.1%.

60Hz voltage for a period of 500 hours at + 85°C.

, Low Loss

Rated DC Voltage

800, 1200, 1600

certain

400, 600

200

solid-state

capacitors. Type 715P capacitors

capacitors are conformally

Maximum 60Hz Voltage

Vishay Sprague

vertical

Type 715P

155

200

500

www.vishay.com

circuits,

Related parts for 715P10356KD3

715P10356KD3 Summary of contents

Page 1

... Megohm-microfarads after test but need not exceed 100,000 Megohm. Not more than one failure in 12 units tested shall be permitted. DC Life Test: Capacitors are capable of withstanding a 500 hour life test at + 85°C at 150% of rated working voltage. After test, capacitance shall not have changed by ...

Page 2

Type 715P Vishay Sprague DIMENSIONS in inches [millimeters] L Max. 0.250 [6.350] Max. 1.250 [31.750] Min. S Terminal A CASE L CODE (Max.) J 0.75 [19.050] K 0.95 [24.130] L 1.30 [33.020] M 1.70 [43.180] PERFORMANCE CHARACTERISTICS + 2 + ...

Page 3

... Shaded items, when ordered as ± 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" "5" to indicate ± 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special. ...

Related keywords

715P10356KD3 datasheet
715P10356KD3 data sheet
715P10356KD3 pdf datasheet
715P10356KD3 component
715P10356KD3 part
715P10356KD3 distributor
715P10356KD3 RoHS
715P10356KD3 datasheet download

715P10356KD3 Vishay Specialty Capacitors, 715P10356KD3 Datasheet

715P10356KD3

Specifications of 715P10356KD3

Related parts for 715P10356KD3

715P10356KD3 Summary of contents

Page 1

Page 2

Page 3

Page 4

Page 5

Page 6

Related keywords