31-212 (UG-260B/U) AMPHENOL RF, 31-212 (UG-260B/U) Datasheet - Page 9

• Manufacturer Part Number: 31-212 (UG-260B/U)
• Description: connector, rf coaxial, bnc straight plug, clamp/solder, rg59, 62, 71, 140, 210, 302, 50ohm
• Manufacturer: AMPHENOL RF
• Type: Cable Plugr

Specifications of 31-212 (UG-260B/U)

• Angle: Straight
• Application: True MIL
• Cable Type: RG/U 140,59,62,71,210,302
• Contact Plating: Silver
• Finish, Housing: Nickel
• Gender: Plug
• Impedance: 50 Ohms
• Material, Contact: Brass (Male), Beryllium Copper⁄Phosphor Bronze (Female)
• Material, Dielectric: TFE/Styrene
• Material, Housing: Brass
• Mating Type: Bayonet
• Primary Type: BNC
• Temperature, Operating: -65 to +165 °C
• Termination: Solder
• Voltage, Rating: 500 V
• Lead Free Status / Rohs Status: RoHS Compliant part

CRIMP TERMINATION FOR TYPE 1 – 75
Assembly Instructions-C31
BNC
Amphenol Corporation Tel: [phone]
31-70000
31-70000-1000
31-70008
31-70008-1000
31-70008-3000
31-70009
31-70013
31-70013-1000
31-70015-1000
31-70016
31-70016-1000
31-70022
31-70082
31-70222
Step 1
Step 2
Step 3
Number
For RG-174, 179, 187, 188, 316/U cables only, slit jacket back .100"(2.5mm)
as shown. Before attaching center contact, slide TFE sleeve (not shown)
over cable dielectric and under braid. The center contact should butt
against the dielectric and TFE sleeve.
Amphenol Connector Cable
75
75
75
75
75
75
75
75
75
75
75
75
75
75
BNC Plug
BNC Plug
BNC Plug
BNC Plug
BNC Plug
BNC Jack
BNC Plug
BNC Plug
BNC Angle Plug
BNC Jack
BNC Bulkh. Jack
BNC Plug
BNC Angle Plug
BNC Plug
Type
outer ferrule
6, Belden 9248, Plenum 6
6, Belden 9248
59
59 (20GA CC)
59 (.032 CC)
59
179, 187
Dbl. Br. 179, ATT19224-L2
Dbl. Br. 179,ATT19224-L2
179, 187
Dbl. Br. 179, ATT19224-L2
ATT 728B, Belden 9231
ATT 735A
Belden 8281, 9231
Hex Crimp Data
a
b
c
RG-/U
crimp contact
in this area
contact
Stripping Dimensions, inches (mm)
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.052(1.3) sq.
.068(1.7)hex
Solder Only
.052(1.3) sq.
Cavity for
Contact
CONNECTORS
306
Step 1 Slide outer ferrule over cables shown. Flare slightly end of
Step 2 Place contact onto center conductor so it butts against cable
Step 3 Install cable assembly into body assembly so inner ferrule
use die set 227-1448 with tool frame 227-944
Outer Ferrule
cable braid as shown to facilitate insertion of inner ferrule.
IMPORTANT: Do not comb out braid.
dielectric. Crimp contact in place.
slides over sleeve and under braid. Push cable assembly
forward until contact seats in insulator. Slide outer ferrule
over braid and up against connector body. Crimp outer
ferrule.
.324(8.2)
.324(8.2)
.255(6.5)
.255(6.5)
.255(6.5)
.255(6.5)
.178(4.5)
.178(4.5)
.178(4.5)
.178(4.5)
.178(4.5)
.324(8.2)
.160(4.1)
.324(8.2)
Cavity for
body assembly
CTL Series
CTL-8
CTL-8
CTL-6 or 8
CTL-6 or 8
CTL-6 or 8
CTL-6 or 8
CTL-6
CTL-6
CTL-6
CTL-6
CTL-6
CTL-8
CTL- 8
Tool No.
.577(14.7)
.577(14.7)
.577(14.7)
.577(14.7)
.577(14.7)
.557(14.1)
.577(14.7)
.594(15.1)
.649(16.5)
.886(22.5)
.886(22.5)
.579(15.1)
.635(16.1)
.577(14.7)
a
Amphenol
.234(5.9)
.234(5.9)
.234(5.9)
.234(5.9)
.234(5.9)
.214(5.4)
.234(5.9)
.250(6.4)
.435(11.0)
.451(11.4)
.451(11.4)
.125(3.2)
.385(9.8)
.234(5.9)
www.amphenolrf.com
b
.140(3.6)
.140(3.6)
.140(3.6)
.140(3.6)
.140(3.6)
.156(4.0)
.140(3.6)
.156(4.0)
.125(3.2)
.140(3.6)
.140(3.6)
.125(3.2)
.200(5.1)
.140(3.6)
c
®