MAX3387EEUG+ Maxim Integrated Products, MAX3387EEUG+ Datasheet - Page 7

• Manufacturer Part Number: MAX3387EEUG+
• Description: IC TXRX RS232 250KBPS 24-TSSOP
• Manufacturer: Maxim Integrated Products
• Type: Transceiverr

Specifications of MAX3387EEUG+

• Number Of Drivers/receivers: 3/3
• Protocol: RS232
• Voltage - Supply: 3 V ~ 5.5 V
• Mounting Type: Surface Mount
• Package / Case: 24-TSSOP
• Propagation Delay Time Ns: 0.15 us
• Operating Supply Voltage: 3.3 V to 5 V
• Supply Current: 0.3 mA
• Operating Temperature Range: - 40 C to + 85 C
• Data Rate: 250 Kbps
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX3387E’s internal power supply consists of a
regulated dual charge pump that provides output volt-
ages of +5.5V (doubling charge pump) and -5.5V
(inverting charge pump), regardless of the input volt-
age (V
pumps operate in a discontinuous mode: if the output
voltages are less than 5.5V, the charge pumps are
enabled; if the output voltages exceed 5.5V, the charge
pumps are disabled. Each charge pump requires a fly-
ing capacitor (C1, C2) and a reservoir capacitor (C3,
C4) to generate the V+ and V- supplies.
The transmitters are inverting level translators that con-
vert CMOS-logic levels to 5.0V EIA/TIA-232 levels.
The MAX3387E transmitters guarantee a 250kbps data
rate with worst-case loads of 3kΩ in parallel with
1000pF, providing compatibility with PC-to-PC commu-
nication software (such as Laplink
be paralleled to drive multiple receivers or mice. Figure 1
shows a complete system connection.
Figure 1. Interface Under Control of PMU
Laplink is a registered trademark of Laplink Software, Inc.
POWER SUPPLY
MANAGEMENT
CONTROLLER
CPU
KEYBOARD
3V, ±15kV ESD-Protected, AutoShutdown Plus
POWER-
UNIT OR
RS-232 Transceiver for PDAs and Cell Phones
I/O CHIP
CC
) over a +3.0V to +5.5V range. The charge
UART
CHIP
WITH
FORCEON
FORCEOFF
INVALID
V
_______________________________________________________________________________________
I/O
CC
Detailed Description
RS-232 Transmitters
V
Dual Charge-Pump
L
Voltage Converter
MAX3387E
®
). Transmitters can
RS-232
These RS-232 output stages are turned off (high imped-
ance) when the device is in shutdown mode. When the
power is off, the MAX3387E permits the outputs to be
driven up to ±12V.
The transmitter inputs do not have pull-up resistors.
Connect unused inputs to GND or V
The receivers convert RS-232 signals to CMOS-logic
output levels. The MAX3387E’s receivers are always
active, even when the device is in shutdown.
The MAX3387E features an INVALID output that indi-
cates when no signal is present on any RS-232 receiver
inputs. INVALID is independent of other control logic
functions; it indicates the receiver input conditions only
(Figures 2 and 3).
Figure 2a. INVALID Function Diagram, INVALID = Low
Figure 2b. INVALID Function Diagram, INVALID = High
+2.7V
-2.7V
R_IN
TRANSMITTERS ARE ENABLED IF:
ANY RECEIVER INPUT IS GREATER THAN +2.7V OR LESS THAN -2.7V;
ANY RECEIVER INPUT HAS BEEN BETWEEN +0.3V AND -0.3V FOR LESS THAN 30μs.
+0.3V
-0.3V
R_IN
TRANSMITTERS ARE DISABLED, REDUCING SUPPLY CURRENT TO 1μA IF
ALL RECEIVER INPUTS ARE BETWEEN +0.3V AND -0.3V FOR AT LEAST 30μs.
RS-232 Receivers
COUNTER
L
.
30μs
COUNTER
R
30μs
R
INVALID
INVALID
7