VQ1100N-51 SMC Corporation, VQ1100N-51 Datasheet - Page 78

• Manufacturer Part Number: VQ1100N-51
• Description: SOLENOID VALVE, 5 PORT, BASE MOUNTED, PLUG IN TYPE, 24VDC, -COM
• Manufacturer: SMC Corporation
• Type: Solenoidr

Specifications of VQ1100N-51

• Brand/series: VQ Series
• Configuration: 2-Position Single
• Enclosure Rating: IP65
• Fluid Type: Air/Inert Gas
• Number Of Ports: 5
• Pressure, Operating: 0.7 MPa
• Primary Type: Solenoid Valve
• Temperature, Ambient: –10° to +50°C
• Valve Type: 5-Port Solenoid, Plug-In, Base Mounted with 2 Position Actuation, Rubber Seal, Negative Common
• Voltage, Coil: 24 VDC

These safety instructions are intended to prevent hazardous situations and/or equipment damage.
These instructions indicate the level of potential hazard with the labels of “Caution,” “Warning” or
“Danger.” They are all important notes for safety and must be followed in addition to International
Back page 1
Standards (ISO/IEC), Japan Industrial Standards (JIS)
1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
2) Labor Safety and Sanitation Law, etc.
1. The compatibility of the product is the responsibility of the person who designs the equipment
2. Only personnel with appropriate training should operate machinery and equipment.
3. Do not service or attempt to remove product and machinery/equipment until safety is confirmed.
4. Contact SMC beforehand and take special consideration of safety measures if the product is to
ISO 4413: Hydraulic fluid power – General rules relating to systems.
IEC 60204-1: Safety of machinery – Electrical equipment of machines. (Part 1: General requirements)
ISO 10218-1992: Manipulating industrial robots - Safety.
JIS B 8370: General rules for pneumatic equipment.
JIS B 8361: General rules for hydraulic equipment.
JIS B 9960-1: Safety of machinery – Electrical equipment of machines. (Part 1: General requirements)
JIS B 8433-1993: Manipulating industrial robots – Safety.
etc.
or decides its specifications.
Since the product specified here is used under various operating conditions, its compatibility with specific equipment must be
decided by the person who designs the equipment or decides its specifications based on necessary analysis and test results.
The expected performance and safety assurance of the equipment will be the responsibility of the person who has determined
its compatibility with the product. This person should also continuously review all specifications of the product referring to its
latest catalog information, with a view to giving due consideration to any possibility of equipment failure when configuring the
equipment.
The product specified here may become unsafe if handled incorrectly. The assembly, operation and maintenance of machines or
equipment including our products must be performed by an operator who is appropriately trained and experienced.
1. The inspection and maintenance of machinery/equipment should only be performed after measures to prevent falling or
2. When the product is to be removed, confirm that the safety measures as mentioned above are implemented and the power
3. Before machinery/equipment is restarted, take measures to prevent unexpected operation and malfunction.
be used in any of the following conditions.
1. Conditions and environments outside of the given specifications, or use outdoors or in a place exposed to direct sunlight.
2. Installation on equipment in conjunction with atomic energy, railways, air navigation, space, shipping, vehicles, military,
3. An application which could have negative effects on people, property, or animals requiring special safety analysis.
4. Use in an interlock circuit, which requires the provision of double interlock for possible failure by using a mechanical protective
Caution:
Warning:
Danger :
runaway of the driven objects have been confirmed.
from any appropriate source is cut, and read and understand the specific product precautions of all relevant products
carefully.
medical treatment, combustion and recreation, or equipment in contact with food and beverages, emergency stop circuits,
clutch and brake circuits in press applications, safety equipment or other applications unsuitable for the standard
specifications described in the product catalog.
function, and periodical checks to confirm proper operation.
Caution
moderate injury.
Warning
serious injury.
Danger
injury.
Safety Instructions
indicates a hazard with a high level of risk which, if not avoided, will result in death or serious
indicates a hazard with a low level of risk which, if not avoided, could result in minor or
indicates a hazard with a medium level of risk which, if not avoided, could result in death or
Warning
1)
and other safety regulations
2)
.