BPA60 Bogen Communications, Inc., BPA60 Datasheet - Page 2

• Manufacturer Part Number: BPA60
• Description: Amplifier; 60 W (RMS); 20 Hz to 20 kHz; 85 dB (Below Rated Output); 19 lbs.
• Manufacturer: Bogen Communications, Inc.

Specifications of BPA60

• Controls: Illuminated On⁄Off Power Switch (Front Panel), Input Level Control, Circuit Breaker Reset, Lo Cut Filter Switch (Rear Panel)
• Dimensions: 15-1⁄4 in. W x 3-1⁄2 in. H x 8 in. D
• Frequency Response: 20 Hz to 20 kHz
• Hum And Noise: 85 dB (Below Rated Output)
• Mounting Type: Rack Panel Kit
• Power Consumption: 180 W @ 120 VAC, 60 Hz
• Power Output: 60 W (RMS)
• Protection: Transient Protection Diodes, Electrical Circuit Breaker, 221°F (105°C) Thermostat
• Sensitivity: High Impedance, 300 mV, Low Impedance Balanced, with Optional Transformer, 75 mV
• Standards: UL Listed, CSA Certified
• Weight, Shipping: 19 lbs.

*This receptacle will be grounded only if the power amplifier has been grounded properly.
Specifications
and Engineer
Specifications
Architect
Auxiliary Receptacle (not switched):
Technical
Operating Temperature Range:
The amplifier shall be a Bogen BPA60 power amplifier
or approved equivalent. It shall be of solid-state con-
struction and shall have integrated circuits, silicon
transistors and diodes to provide for continuous high-
quality sound.
The rated output shall be achieved with an input sig-
nal not greater than 300mV (75mV with Model TL600
accessory transformer). The frequency response shall
be flat within -2dB, from 20Hz to 20kHz. Hum and
noise shall be at least 85dB below rated output.
Output regulation shall be better than 2dB from no
load to full load.
The amplifier shall supply 60 watts RMS from 50Hz to
15kHz at less than 2% THD into rated load imped-
ances. Output impedances shall be 8-ohms/25V, 16-
ohms, 25VCT and 70V. Power consumption shall not
exceed 180 watts at full rated output. The amplifier
shall measure 15-1/4"W x 3-1/2"H x 8"D ; weight shall
not exceed 19 lbs.
Input impedances shall be: unbalanced, high impedance
(50k-ohms); balanced/unbalanced, low impedance
(600-ohms) with accessory transformer. Line bridging
shall be possible using an accessory transformer.
Overall gain shall be adjustable by means of an input
level control located on the rear panel. A lo-cut filter
switch shall provide -10dB attenuation at 100Hz.
Total Harmonic Distortion:
Controls and Indicators:
Rated Output Power:
Overload Protection:
Frequency Response:
Power Consumption:
Output Regulation:
Input Impedances:
Input Sensitivity:
Hum and Noise:
Output Loads:
Lo-cut Filter:
Dimensions:
Accessories:
Weight:
Finish:
60 watts RMS
Less than 2% from 50Hz to 15kHz
-2dB, 20Hz to 20kHz
High-impedance, 300mV; low-impedance balanced, with optional
transformer, 75mV
85dB below rated output
8-ohm/25V, 16-ohms, 25VCT, 70V
Better than 2dB from no load to full load
High-impedance, 50k-ohms unbalanced; low-impedance, 600 ohms,
balanced or unbalanced; 1:1 bridging with accessory transformer
-10dB at 100Hz (switch-selectable)
Front Panel — Illuminated on/off power switch
Rear Panel — Input level control, circuit breaker reset, lo-cut filter
switch
120V AC, 60Hz, 180W at full rated output
Transient protection diodes, electrical circuit breaker,
221°F (105° C) thermostat
-4°F to +131°F (-20° to +55° C) at rated output
Three-wire grounded,* 300W maximum
15-1/4"W x 3-1/2"H x 8"D
Black
19 lbs.
Model TL600, 600-ohm line-matching transformer;
Model TL100, 1:1 ratio transformer
Model RPK53 rack panel brackets
The amplifier shall operate within a temperature
range of -4°F to +131°F (-20° C to +55° C.) A ther-
mostat control shall be provided to prevent operation
at excessive ambient temperatures. Additional over-
load protection shall be provided by transient protec-
tion diodes and a resettable electric circuit breaker.
The amplifier shall contain an illuminated on/off power
switch, and shall operate from a 120V AC, 60Hz
source. An auxiliary power receptacle (not switched)
shall be provided, which shall be grounded, provided
that the amplifier line cord is properly grounded.
The amplifier shall be designed for mounting within a
standard 19-inch EIA equipment rack, using optional
rack panel brackets.
50 Spring Street, Ramsey, NJ 07446, U.S.A.
Tel: [phone]; Fax: [phone]; www.bogen.com