TJA1054T/VM,518 NXP Semiconductors, TJA1054T/VM,518 Datasheet - Page 2

• Manufacturer Part Number: TJA1054T/VM,518
• Description: IC TXRX CAN FAULT-TOL 14SOIC
• Manufacturer: NXP Semiconductors
• Type: Transceiverr

Specifications of TJA1054T/VM,518

• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Drivers/receivers: 1/1
• Protocol: CAN
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 125 KBd
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current (max): 27 mA
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 935287981518

NXP Semiconductors
3. Quick reference data
TJA1054
Product data sheet
2.3 Protections
2.4 Support for low power modes
Table 1.
V
defined with respect to ground; positive currents flow into the device; unless otherwise specified.
[1]
[2]
[3]
Symbol Parameter
V
V
I
V
V
ΔV
ΔV
t
t
t
T
BAT
PD(L)
r
f
CC
vj
CC
BAT
CANH
CANL
CANH
CANL
Bus pins short-circuit safe to battery and to ground
Thermally protected
Bus lines protected against transients in an automotive environment
An unpowered node does not disturb the bus lines
Low current sleep mode and standby mode with wake-up via the bus lines
Power-on reset flag on the output
= 4.75 V to 5.25 V; V
All parameters are guaranteed over the virtual junction temperature range by design, but only 100 % tested
at T
unless otherwise specified.
For bare die, all parameters are only guaranteed if the back side of the die is connected to ground.
A local or remote wake-up event will be signalled at the transceiver pins RXD and ERR if
V
BAT
amb
= 5.3 V to 27 V see
supply voltage
battery supply voltage on
pin BAT
battery supply current on
pin BAT
voltage on pin CANH
voltage on pin CANL
voltage drop on pin CANH I
voltage drop on pin CANL I
propagation delay TXD
(LOW) to RXD (LOW)
bus line output rise time
bus line output fall time
virtual junction
temperature
= 125 °C for dies on wafer level, and above this for cased products 100 % tested at T
Quick reference data
All information provided in this document is subject to legal disclaimers.
BAT
Rev. 4 — 3 August 2010
Table
= 5.0 V to 27 V; V
5.
V
V
between 10 % and 90 %;
Conditions
no time limit
operating mode
load dump
sleep mode; V
V
V
with respect to
any other pin
V
with respect to
any other pin
between 10 % and 90 %;
C1 = 10 nF; see
C1 = 1 nF; see
CANH
CANL
BAT
CC
BAT
CC
BAT
= 0 V to 5.0 V;
= 0 V to 5.0 V;
= 12 V
≥ 0 V; no time limit;
≥ 0 V; no time limit;
= 40 mA
= −40 mA
STB
= V
CC
Figure 5
CC
Figure 5
= 0 V;
; T
vj
=
Fault-tolerant CAN transceiver
−
40
[3]
[4]
°
C to +150
Min
4.75
−0.3
5.0
-
-
−40
−40
-
-
-
-
-
−40
Typ
-
-
-
-
30
-
-
-
-
1
0.6
0.3
-
TJA1054
© NXP B.V. 2010. All rights reserved.
°
C; all voltages are
40
Max
5.25
+40
27
50
+40
+40
1.4
1.4
-
-
-
+150
amb
= 25 °C,
Unit
V
V
V
V
μA
V
V
V
V
μs
μs
μs
°C
2 of 25
[1][2]