TJA1054AT/VM,518 NXP Semiconductors, TJA1054AT/VM,518 Datasheet - Page 4

• Manufacturer Part Number: TJA1054AT/VM,518
• Description: IC TXRX CAN FAULT-TOL 14SOIC
• Manufacturer: NXP Semiconductors
• Type: Transceiverr

Specifications of TJA1054AT/VM,518

• Package / Case: 14-SOIC (3.9mm Width), 14-SOL
• Number Of Drivers/receivers: 1/1
• Protocol: CAN
• Voltage - Supply: 4.75 V ~ 5.25 V
• Mounting Type: Surface Mount
• Product: Controller Area Network (CAN)
• Number Of Transceivers: 1
• Data Rate: 125 KBd
• Supply Voltage (max): 5.25 V
• Supply Voltage (min): 4.75 V
• Supply Current (max): 27 mA
• Maximum Operating Temperature: + 150 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Power Down Mode: Sleep/Standby
• Operating Supply Voltage (max): 5.25V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.75V
• Package Type: SO
• Operating Temperature (max): 150C
• Operating Temperature (min): -40C
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 14
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 568-5077-2; 935287974518; TJA1054AT/VM,518

NXP Semiconductors
6. Pinning information
TJA1054A
Product data sheet
6.1 Pinning
6.2 Pin description
Table 3.
Symbol
INH
TXD
RXD
ERR
STB
EN
WAKE
RTH
RTL
V
CANH
CANL
GND
BAT
Fig 2. Pin configuration
CC
Pin description
All information provided in this document is subject to legal disclaimers.
Pin
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Rev. 5 — 3 August 2010
Description
inhibit output for switching an external voltage regulator if a
wake-up signal occurs
transmit data input for activating the driver to the bus lines
receive data output for reading out the data from the bus lines
error, wake-up and power-on indication output; active LOW in
normal operating mode when a bus failure is detected; active LOW
in standby and sleep mode when a wake-up is detected; active
LOW in power-on standby when a V
detected
standby digital control signal input; together with the input signal
on pin EN this input determines the state of the transceiver;
see
enable digital control signal input; together with the input signal on
pin STB this input determines the state of the transceiver;
see
local wake-up signal input (active LOW); both falling and rising
edges are detected
termination resistor connection; in case of a CANH bus wire error
the line is terminated with a predefined impedance
termination resistor connection; in case of a CANL bus wire error
the line is terminated with a predefined impedance
supply voltage
HIGH-level CAN bus line
LOW-level CAN bus line
ground
battery supply voltage
WAKE
RXD
ERR
TXD
STB
INH
EN
Table 5
Table 5
1
2
3
4
5
6
7
and
and
TJA1054AT
Figure 3
Figure 3
001aaf609
14
13
12
11
10
9
8
BAT
GND
CANL
CANH
V
RTL
RTH
CC
Fault-tolerant CAN transceiver
BAT
power-on event is
TJA1054A
© NXP B.V. 2010. All rights reserved.
4 of 27