MAX3867ECM Maxim Integrated Products, MAX3867ECM Datasheet
MAX3867ECM
Specifications of MAX3867ECM
Available stocks
Related parts for MAX3867ECM
MAX3867ECM Summary of contents
Page 1
... Automatic Average Power Control with Failure Monitor Complies with ANSI, ITU, and Bellcore SDH/SONET Specifications Enable Control PART Applications MAX3867ECM MAX3867E/D * Dice are designed to operate over this range, but are tested and guaranteed at T Pin Configuration appears at end of data sheet. 124 DATA+ ...
Page 2
SDH/SONET Laser Driver with Automatic Power Control ABSOLUTE MAXIMUM RATINGS Supply Voltage, V ............................................. -0.5V to +7.0V CC Current into BIAS ...........................................-20mA to +150mA Current into OUT+, OUT- ................................-20mA to +100mA Current into MD.....................................................-5mA to +5mA Voltage at ...
Page 3
... MOD (Note 6) t 20% to 80% (Note 20% to 80% (Note 8) F (Note 8) (Notes 8, 9) Jitter BW = 12kHz to 20MHz, 0-1 pattern = +3.3V 30mA, and T CC MOD MIN TYP 100 100 5 -480 -50 250 -15 MAX3867ECM 79 MAX3867C/D 69 MAX3867ECM 88 (Note 10) MAX3867C/D 79 ±15 250 MAX UNITS 200 µA 480 ppm/° ...
Page 4
SDH/SONET Laser Driver with Automatic Power Control DATA+ DATA- (DATA+) - (DATA-) I Figure 1. Required Input Signal and Output Polarity ARE SMD FERRITE BEADS BLM11A601S MURATA ELECTRONICS A = ...
Page 5
SDH/SONET Laser Driver (V = +3.3V, load as shown in Figure EYE DIAGRAM (2.488Gbps, 1300nm FP LASER, 1.87GHz FILTER, 48-TQFP) 50ps/div ELECTRICAL EYE DIAGRAM 26mV /div PATTERN = CID ...
Page 6
SDH/SONET Laser Driver with Automatic Power Control (V = +3.3V, load as shown in Figure SUPPLY CURRENT vs. TEMPERATURE (EXCLUDE LOAD) BIAS MOD 100 + ...
Page 7
SDH/SONET Laser Driver PIN NAME 25 BIAS 29 OUT+ 30 OUT 34, 36, 40 GND3 CAPC 44 APCSET 46 MODSET 47 BIASMAX _______________Detailed Description The MAX3867 laser ...
Page 8
SDH/SONET Laser Driver with Automatic Power Control LATCH MAX3867 0 MUX DATA CLK ENABLE 172X MODSET BIASMAX R R MODSET BIASMAX Figure 4. Functional Diagram laser package is used to convert the optical power into ...
Page 9
SDH/SONET Laser Driver and MODSET. See the Design Procedure section for more details on open-loop operation. Optional Data Input Latch To minimize input data pattern-dependent jitter, the dif- ferential clock signal should be connected to the data input ...
Page 10
SDH/SONET Laser Driver with Automatic Power Control pattern-dependent jitter, three external components must be properly chosen: capacitor C nates the APC loop time constant; pull-up inductor L and AC-coupling capacitor filter out noise effects ...
Page 11
SDH/SONET Laser Driver Modulation Current More than 60mA At +5V power supply, the headroom voltage for the MAX3867 is significantly improved. In this case possible to achieve a modulation current of more than 60mA with AC-coupling, ...
Page 12
... Maxim product could create a situation where personal injury or death may occur. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 1998 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products ...