1-1376390-2 TE Connectivity, 1-1376390-2 Datasheet
1-1376390-2
Specifications of 1-1376390-2
Available stocks
Related parts for 1-1376390-2
1-1376390-2 Summary of contents
Page 1
... Tel ０４４‐８４４‐８０７９ Fax ０４４‐８１２‐３２０３ ...
Page 2
... C. ダブルロックプレート : 6/6 ナイロン (ガラス強化 V-0 トラッキングインデックス : 175～250 V D. ヘッダー･アセンブリ ...
Page 3
... C. Temperature Rating D. Minimum Rating E. Applicable P.C.B Diameter of Thehole : For Tine : For Boss : 1.3±0.05(Punched Hole & Drilled Hole) 3.4 Performance Requirements and Test Descriptions : The product shall be designed to meet the electrical, mechanical and environmental performance requirements specified in Fig.3. All tests shall be performed in the room temperature unless otherwise specified ...
Page 4
... No physical damage Electrical Requirements 3.5.2 Termination Resistance (Low Level Max. (Initial Max. (Final) Subject mated contacts assembled in housing to 20mV Max. open circuit at 10mA. Take the resistance of the wire only away from measurement Fig. 7. EIA 364-23 3.5.3 Insulation Resistance 1000 M Min. (Initial) 500 M Min ...
Page 5
... Test between adjacent circuits and between the surface of housing and contact of mated connectors. EIA 364-20 3.5.5 Temperature Rising 30℃ Max. under loaded specified current. Measure temperature rising by energized current. Subject measurement must do at the place of no influence from convection of air. And contacts assembled in housing all of circuits ...
Page 6
... No electrical discontinuity greater than 1 µsec. shall occur Max. (Final) No electrical discontinuity greater than 1 µsec. shall occur Max. (Final) Subject mated connectors to 10-55-10 Hz traversed in 1 minute at 1.52mm amplitude 2 hours each of 3 mutually perpendicular planes. 100 mA applied. Fig. 8 MIL-STD-202, Method 201A EIA 364-28 3.5.7 ...
Page 7
... EIA 364-29 3.5.10 Contact Retention Force 39.2 N (4.0kgf) Min. Apply an axial pull-off load to crimped wire. Use the wire of AWG #16 or AWG #18 Operation Speed : 100 mm / min. EIA 364-29 Fig. 3 (続く) (To be Continued) 108-5699 (9.8×Pos.)N Max. (1.0×Pos.)kg Max. ...
Page 8
... Apply an axial pull-off load to crimped wire of contact secured on the tester, Operation Speed : 100 mm/min. Subject take insulation barrel away. IEC-60512-9-1 3.5.13 Durability (Repeated Mate/Unmating Max. (9.8×Pos.)N Max. Mating (1.0×Pos.)kg Max. Unmat- (1.47× ...
Page 9
... Procedures これを 1 サイクルとし 25 サイクル行う｡ MIL-STD-202 試験法 107-1 条件 A-1 EIA 364-32 但し､測定は室内放置 3 時間後行う｡ ...
Page 10
... Insulation resistance (final) 500 M Min. 以上 (終期) Termination resistance 20 m Max. (Final) 以下 (終期) Mated connector, 25～65℃, 80～ cycles Cold shock －10℃(not ) performed MIL-STD-202, Method 106 Condition D The measurement is held after being left indoor for 3 hours ...
Page 11
... The Measurement is held after being left indoor for 3 hours. 3.5.20 Resistance to Cold 20 m Max. (Final) Mated connector -30℃±2℃, 96 hours EIA 364-59 3.5. Max. (Final) No corrosion influence performance Mated connector 3±1 ppm, 40±2℃ 96 hours Fig. 3 (続く) (To be Continued) 108-5699 ...
Page 12
... NH 3.5.23 Solderability Wet Solder Coverage : 90 % Min. : 230±5℃ Solder Temperature : 230 ± 5℃ Immersion Duration : 3 ± 0.5 seconds MIL-STD-202 Method 208 3.5.24 Resistance to Soldering Heat No physical damage shall occur. Test connector on PCB. Solder Temperature : 260±5℃ 260±5℃ ...
Page 13
... Rev.E 5mm Power Key Connector 5mm パワー キイ コネクタ 3.6 Product Qualification Test Sequence 試験グループ 試 験 順 序 Test Sequence (a) 1,3 1,4 1 ...
Page 14
... Test Sequence (a) 1,4 1,4 1,4 1,4 2,5 2,5 2,5 2 (a) Numbers indicate the sequence in which the tests are performed. Fig. 4(2/2) 108-5699 試験グループ Test Group 試 験 順 序 1,4 1,4 1,3 1,3 1,3 2,5 2 Rev ...
Page 15
... The crimped contacts shall be prepared in accordance with the requirements of applicable application Specification, 114-5292, Crimping of 5mm Pitch W-T-B Connector on the wires specified in Fig this specification. 4.2.2 Applicable Wires : The wires to be used for crimping the samples for ｐerformance testing shall be conforming to the requirements specified in Fig. 6. 素 ...
Page 16
... Fig. 7 Termination Resistance (Low Level) and Temperature Rising Vs. Current Measuring Methods 5mm Power Key Connector 5mm パワー キイ コネクタ Fig. 7 総合抵抗 (ローレベル)､温度上昇 108-5699 ...
Page 17
... Fig. 8 Connector Mounting Methods of Low Frequency Vibration and Physical Shock Tests Rev.E 5mm Power Key Connector 5mm パワー キイ コネクタ Fig. 8 低周波振動､物理的衝撃のコネクタ取付方法 108-5699 ...
Page 18
... Fig. 9 Gage Design for Contact Meting/Unmating Force Tests 5mm Power Key Connector 5mm パワー キイ コネクタ Fig. 9 コンタクト挿入引抜力測定用ゲージ 108-5699 Rev. E ...
Page 19
... Pos. 極数 Rev.E 5mm Power Key Connector 5mm パワー キイ コネクタ 品 名 Name AWG #20～#16 AWG #24～#20 1列タイプ Single Row Type Plug Housing 2列 ...