DG403DY+ Maxim Integrated Products, DG403DY+ Datasheet - Page 5

• Manufacturer Part Number: DG403DY+
• Description: IC SWITCH DUAL DPST 16SOIC
• Manufacturer: Maxim Integrated Products
• Type: Analog Switchr

Specifications of DG403DY+

• Function: Switch
• Circuit: 2 x DPST - NC/NO
• On-state Resistance: 45 Ohm
• Voltage Supply Source: Single, Dual Supply
• Voltage - Supply, Single/dual (±): 10 V ~ 30 V, ±4.5 V ~ 20 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Number Of Switches: Dual
• Switch Configuration: SPST
• On Resistance (max): 45 Ohms
• On Time (max): 150 ns
• Off Time (max): 100 ns
• Off Isolation (typ): 72 dB
• Supply Voltage (max): +/- 20 V
• Supply Voltage (min): +/- 5 V
• Supply Current: 0.001 uA
• Maximum Power Dissipation: 696 mW
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Description/function: Analog Switch
• Input Level: CMOS, TTL
• Minimum Operating Temperature: - 40 C
• Off State Leakage Current (max): 0.5 nA
• Package: 16SOIC N
• Maximum On Resistance: 45@±13.5V Ohm
• Maximum High Level Output Current: 30 mA
• Number Of Channels Per Chip: 2
• Maximum Turn-off Time: 100@±15V ns
• Maximum Turn-on Time: 150@±15V ns
• Switch Architecture: SPDT
• Power Supply Type: Single|Dual
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

_____________________Pin Description
16, 9, 4, 5
16, 9, 4, 5
1, 8, 3, 6
1, 8, 3, 6
DIP/SO
DIP/SO
DIP/SO
10, 15
10, 15
10, 15
9, 16
1, 8
2, 7
2, 7
2-7
11
12
13
14
11
12
13
14
11
12
13
14
Improved, Dual, High-Speed Analog Switches
DG401
DG403
DG405
2, 10, 4, 8
2, 10, 4, 8
1, 3, 6, 9,
1, 3, 6, 9,
20, 12,
20, 12,
1, 3-9,
11, 16
12, 20
13, 19
11, 16
13, 19
11, 16
13, 19
2, 10
LCC
LCC
LCC
5, 7,
5, 7,
14
15
17
18
14
15
17
18
14
15
17
18
_______________________________________________________________________________________
IN2, IN1 Digital Logic Inputs
IN2, IN1 Digital Logic Inputs
IN2, IN1 Digital Logic Inputs
D1, D2
NAME
NAME
NAME
S2, S1
D1-D4
D1-D4
S1-S4
S1-S4
GND
GND
GND
N.C.
N.C.
N.C.
V+
V+
V+
V
V
V
V-
V-
V-
L
L
L
Drain (Analog Signal)
Not internally connected
Source (Analog Signal)
Positive Supply-Voltage
Input—connected to
substrate
Logic Supply-Voltage Input
Ground
Negative Supply-Voltage
Input
Drain (Analog Signal)
Not internally connected
Source (Analog Signal)
Positive Supply-Voltage
Input—connected to
substrate
Logic Supply-Voltage Input
Ground
Negative Supply-Voltage
Input
Drain (Analog Signal)
Not internally connected
Source (Analog Signal)
Positive Supply-Voltage
Input—connected to
substrate
Logic Supply-Voltage Input
Ground
Negative Supply Voltage
FUNCTION
FUNCTION
FUNCTION
The DG401/DG403/DG405 switches operate with
±4.5V to ±20V bipolar supplies or with a +10V to +30V
single supply. In either case, analog signals ranging
from V+ to V- can be switched. The Typical Operating
Characteristics graphs illustrate typical analog-signal
and supply-voltage on-resistance variations. The usual
on-resistance temperature coefficient is 0.5%/°C (typ).
These devices operate with a single positive supply or
with bipolar supplies. They maintain TTL compatibility
with supplies anywhere in the ±4.5V to ±20V range as
long as V
supply at voltages other than +5V, the devices will
operate at CMOS-logic-level inputs.
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute
maximum ratings because stresses beyond the listed
ratings may cause permanent damage to the devices.
Always sequence V+ on first, followed by V
logic inputs. If power-supply sequencing is not
possible, add two small, external signal diodes in
series with supply pins for overvoltage protection
(Figure 1). Adding diodes reduces the analog-signal
range to 1V below V+ and 1V below V-, without affect-
ing low switch resistance and low leakage
characteristics. Device operation is unchanged, and
the difference between V+ and V- should not exceed
+44V.
Figure 1. Overvoltage Protection Using External Blocking Diodes
__________Applications Information
V
g
L
= +5V. If V
Operation with Supply Voltages
S
L
is connected to V+ or another
Overvoltage Protection
V+
V-
Other than ±15V
D
Logic Inputs
L
, V-, and
5