ADG729BRUZ Analog Devices Inc, ADG729BRUZ Datasheet - Page 6

• Manufacturer Part Number: ADG729BRUZ
• Description: IC MUX/DEMUX DUAL 4X1 16TSSOP
• Manufacturer: Analog Devices Inc

Specifications of ADG729BRUZ

• Function: Multiplexer/Demultiplexer
• Circuit: 2 x 4:1
• On-state Resistance: 4.5 Ohm
• Voltage Supply Source: Single Supply
• Voltage - Supply, Single/dual (±): 2.7 V ~ 5.5 V
• Current - Supply: 10µA
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-TSSOP (0.173", 4.40mm Width)
• No. Of Circuits: 2
• Supply Current: 10µA
• On State Resistance Max: 2.5ohm
• Supply Voltage Range: 2.7V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Analog Switch Case Style: TSSOP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ABSOLUTE MAXIMUM RATINGS
(T
V
Analog, Digital Inputs
Peak Current, S or D . . . . . . . . . . . . . . . . . . . . . . . . . . 100 mA
Continuous Current, Each S . . . . . . . . . . . . . . . . . . . . . 30 mA
Continuous Current D, ADG729 . . . . . . . . . . . . . . . . . 80 mA
Continuous Current D, ADG728 . . . . . . . . . . . . . . . . 120 mA
Operating Temperature Range
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
V
I
GND
S
D
V
R
∆R
R
I
I
I
V
V
I
C
C
ADG728/ADG729
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the ADG728/ADG729 features proprietary ESD protection circuitry, permanent damage
may occur on devices subjected to high-energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
DD
S
D
D
INL
DD
DD
D
ON
FLAT(ON)
INL
INH
S
D
A
Industrial (B Version) . . . . . . . . . . . . . . . . –40°C to +85°C
, I
(OFF)
(OFF)
ON
= 25°C unless otherwise noted.)
(OFF)
(V
(OFF)
(I
S
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
(ON)
S
INH
)
)
Most Positive Power Supply Potential.
Positive Supply Current.
Ground (0 V) Reference.
Source Terminal. May be an input or output.
Drain Terminal. May be an input or output.
Analog Voltage on Terminals D, S.
Ohmic Resistance between D and S.
On Resistance Match Between any Two Chan-
nels, i.e., R
Flatness is defined as the difference between the
maximum and minimum value of on resistance
as measured over the specified analog signal range.
Source Leakage Current with the Switch “OFF.”
Drain Leakage Current with the Switch “OFF.”
Channel Leakage Current with the Switch “ON.”
Maximum Input Voltage for Logic “0.”
Minimum Input Voltage for Logic “1.”
Input Current of the Digital Input.
“OFF” Switch Source Capacitance. Measured
with reference to ground.
“OFF” Switch Drain Capacitance. Measured
with reference to ground.
2
. . . . . . . . . . –0.3 V to V
(Pulsed at 1 ms, 10% Duty Cycle max)
ON
max – R
30 mA, Whichever Occurs First
ON
1
min.
DD
+ 0.3 V or
TERMINOLOGY
TSSOP Package
Lead Temperature, Soldering (10 seconds) . . . . . . . . . . 300°C
IR Reflow, Peak Temperature . . . . . . . . . . . . . . . . . . . . 220°C
NOTES
1
2
C
C
t
t
t
Charge
Injection
Off Isolation
Crosstalk
Bandwidth
On Response The frequency response of the “ON” switch.
Insertion
Loss
Stresses above those listed under Absolute Maximum Ratings may cause perma-
Overvoltages at IN, S or D will be clamped by internal diodes. Current should be
ON
OFF
D
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those listed in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability. Only one absolute
maximum rating may be applied at any one time.
limited to the maximum ratings given.
D
IN
θ
θ
, C
JA
JC
Thermal Impedance . . . . . . . . . . . . . . . . . . . 150.4°C/W
Thermal Impedance . . . . . . . . . . . . . . . . . . . . 27.6°C/W
S
(ON)
ence to ground.
of the STOP condition and the switch “ON”
condition.
of the STOP condition and the switch “OFF”
condition.
both switches when switching from one switch to
another.
switching.
an “OFF” switch.
through from one channel to another as a result
of parasitic capacitance.
The frequency at which the output is attenuated
by 3 dBs.
The loss due to the ON resistance of the switch.
“ON” Switch Capacitance. Measured with refer-
Digital Input Capacitance.
Delay time between the 50% and 90% points
Delay time between the 50% and 90% points
“OFF” time measured between the 80% points of
A measure of the glitch impulse transferred from
the digital input to the analog output during
A measure of unwanted signal coupling through
A measure of unwanted signal which is coupled
WARNING!
ESD SENSITIVE DEVICE