ASI PROGRAMMER V2.0 ZMDI, ASI PROGRAMMER V2.0 Datasheet
ASI PROGRAMMER V2.0
Specifications of ASI PROGRAMMER V2.0
Related parts for ASI PROGRAMMER V2.0
ASI PROGRAMMER V2.0 Summary of contents
Page 1
AS –Interface Programmer User Manual User Manual AS-Interface Programmer Notice: R ESTRICTIONS T ZMD AS NTERFACE ROGRAMMER HARDWARE AND IC DESIGNED FOR EVALUATION T ZMD AS NTERFACE ROGRAMMER HARD AND PRODUCTION TEST SETUPS ZMD AG SHALL ...
Page 2
AS –Interface Programmer User Manual Table of Contents 1 HARDWARE ..................................................................................................................................... 3 1.1 B ......................................................................................................................... 3 OARD DESCRIPTION 1.2 H ............................................................................................................................ 4 ARDWARE SETUP 1.2.1 ASi Bus powered setup ............................................................................................................... 4 1.2.2 Internal ASI power generation ..................................................................................................... 5 1.2.3 Master ...
Page 3
AS –Interface Programmer User Manual 1 Hardware 1.1 Board description Input 30V +/- CMOS Interface ASI + / ASI - LED 5 ASI+ / ASI-: Connection to the ASi network. The Programmer runs as AS-i Master. In AS-i mode (LED5 ...
Page 4
AS –Interface Programmer User Manual RS232 interface: connection to PC (19200 Baud, 8 bit, no parity, 1 stop bit). Connect this port with the enclosed cable to a free serial COM port at your PC. After program start, the ASI ...
Page 5
AS –Interface Programmer User Manual 1.2.2 Internal ASI power generation Laboratory DC Laboratory DC Power Supply Power Supply ... ... 1...62 ASi Slave modules 1...62 ASi Slave modules The power supply of the complete system, including ASI modules and ASI ...
Page 6
AS –Interface Programmer User Manual 2 Software 2.1 Setup and Installation System requirements: 486 compatible PC, 8MB RAM, 12MB free HDD, free COM port If the PC do not support a free COM port, the ASI Programmer can be connected ...
Page 7
AS –Interface Programmer User Manual 2.2.2 Main window Graphical Input Output Manual network / slave control control 2.2.3 Graphical Input Output Control This module allows to control an AS-Interface network ( slave modules) bit by bit. Graphical Input ...
Page 8
AS –Interface Programmer User Manual 5. The slave input data are shown by ed circles (=“0“) and green circles (=“1“). Output ports can be changed by setting a check mark in the corresponding field. 6. All outputs will be erased ...
Page 9
AS –Interface Programmer User Manual Parameter Parameter Data output to the slave data input from slave Rev. 1.08, Copyright © 2005, ZMD AG All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used ...
Page 10
AS –Interface Programmer User Manual 2.2.5 Change address New slave address, Slave to address normal addressing mode (A/B Slave) 1. Select a slave to change address 2. Select a new slave address ( the select menus show only free network ...
Page 11
AS –Interface Programmer User Manual 2.2.6 EEPROM Configuration To program EEPROM functions only 1 slave with address „0“ should be connected to the network Read EEPROM 1. Click on „Read IC Configuration“ to read current EEPROM setting change ...
Page 12
AS –Interface Programmer User Manual 2.2.7 Terminal The terminal tool allows the communication with an AS-interface network or a single slave module command by command. Command line input Send command from the command line 1. Type a valid command in ...
Page 13
AS –Interface Programmer User Manual 2.3 Telegram structure 2.3.1 Telegram structure of Standard AS-i telegrams in Terminal Mode Description Command Master request 1 Data Exchange D P Write Parameter Address Assignment A Write Extend. ID-Code 1 E Delete Address C ...
Page 14
AS –Interface Programmer User Manual 2.3.2 Telegram structure of special functions in Terminal Mode Description Command Remarks Scan AS-I Bus W Scans the AS-I bus and reads the configuration data of the connected modules IRD Lock IRD Channel Sends a ...
Page 15
AS –Interface Programmer User Manual 3 Schematics 3.1 ASi and MCU Rev. 1.08, Copyright © 2005, ZMD AG All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent ...
Page 16
AS –Interface Programmer User Manual 3.2 PC Communication Interface Rev. 1.08, Copyright © 2005, ZMD AG All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the ...
Page 17
AS –Interface Programmer User Manual 4 Notes Rev. 1.08, Copyright © 2005, ZMD AG All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without the prior written consent of the copyright owner. ...