LV8086T-TLM-H ON Semiconductor, LV8086T-TLM-H Datasheet - Page 2

• Manufacturer Part Number: LV8086T-TLM-H
• Description: 55T3231
• Manufacturer: ON Semiconductor

Specifications of LV8086T-TLM-H

• Motor Type: Stepper
• No. Of Outputs: 2
• Output Current: 1.4A
• Supply Voltage Range: 2V To 7V
• Driver Case Style: TSSOP
• No. Of Pins: 24
• Operating Temperature Range: -20°C To +75°C
• Svhc: No SVHC
• Rohs Compliant: Yes

Allowable Operating Ratings at Ta = 25°C, SGND = PGND = 0V
Electrical Characteristics at Ta = 25°C, V CC = VM1 = VM2 = 5.0V, SGND = PGND = 0V, unless especially specified.
Ta = 25°C, V CC = VM = 5.0V, SGND = PGND = 0V
Remarks
Supply voltage (VM Pin)
Supply voltage (V CC Pin)
Input signal voltage
Input signal frequenc
Capacitor for charge pump
Supply current for load at standby
Supply current for control at
standby
Current drain during operation
H-level input voltage
L-level input voltage
H-level input current
(IN1, IN2, IN3, IN4)
L-level input current
(IN1, IN2, IN3, IN4)
Pull-down resistance (EN1, 2)
Output ON resistance
Charge pump voltage
Low-voltage detection operation
voltage
Thermal shutdown operation
temperature
Charge pump capacity
(IG = 500μA)
IG current dissipation (Fin = 20kHz)
Charge pump start time
Output block
10. It shows VG pin current dissipation in state of PWM input for IN pin.
11. It specifies start-up time from 10% to 90% when VG is in non-load state
12. It specifies 10% to 90% for start-up and 90% to 10% for shut-down.
1. It shows current dissipation of VM1,2 pin in output OFF state.
2. It shows current dissipation of V CC pin in stand-by state.
3. It shows current dissipation of V CC pin in state of EN = 5V (stand-by), including current dissipation of VG pin.
4. For IN1, IN2, IN3 and IN4 pins, no pull-down and pull-up resistance is needed. (High impedance pin)
5. It shows sum of upper and lower saturation voltages of OUT pin.
6. It controls charge-pump oscillation and makes specified voltage.
7. When low voltage is detected, the lower output is turned OFF.
8. When thermal protection circuit is activated, the lower output is turned OFF.
9. IG (VG pin load current) = 500μA
(The standard current depends on EN pin pull-down resistance.)
When the heat temperature is fallen, it is turned ON again.
(when setting the capacitor between VG and GND to 0.1μF and V CC is 5V).
Parameter
Parameter
Parameter
Turn on time
Turn off time
C1, C2, C3
VGLOAD
Symbol
Symbol
Symbol
TPLH
TPHL
f max
RON
V CC
RUP
VCS
TVG
IMO
ICO
V IN
IC1
V IH
VM
V IL
VG
Tth
I IH
I IL
IG
EN = 0V
EN = 0V, IN1 = IN2 = IN3 = IN4 = 0V
EN = 5V, VG at no load
2.7V ≤ V CC ≤ 5.5V
2.7V ≤ V CC ≤ 5.5V
Sum of ON resistances at top and bottom
CVG = 0.1μF
LV8086T
Conditions
Conditions
Conditions
0.6V CC
min
min
2.15
-1.0
100
8.5
0
8
Ratings
Ratings
Ratings
typ
typ
0.75
2.30
200
180
0.7
0.2
0.2
9
0.001 to 0.1
2.0 to 7.0
2.7 to 5.5
0 to V CC
0.2V CC
max
max
V CC
10.5
2.45
100
400
350
1.0
1.0
1.0
1.2
1.0
0.4
0.4
1.2
No. A1135-2/6
Unit
Unit
Unit
kHz
mA
ms
μF
μA
μA
μA
μA
kΩ
°C
μA
μs
μs
V
V
V
V
V
Ω
V
V
V