LH28F160BJHE-BTLTH Sharp Electronics, LH28F160BJHE-BTLTH Datasheet
LH28F160BJHE-BTLTH
Specifications of LH28F160BJHE-BTLTH
Related parts for LH28F160BJHE-BTLTH
LH28F160BJHE-BTLTH Summary of contents
Page 1
... P S RODUCT PECIFICATION LH28F160BJHE-BTLTH Flash Memory 16Mbit (1Mbitx16 / 2Mbitx8) (Model Number: LHF16JTH) Spec. Issue Date: October 22, 2004 Spec No: EL16X190 Integrated Circuits Group ...
Page 2
...
Page 3
Handle this document carefully for it contains material protected by international copyright law. Any reproduction, full or in part, of this material is prohibited without the express written permission of the company. When using the products covered herein, please observe ...
Page 4
INTRODUCTION.............................................................. 3 1.1 Features ........................................................................ 3 1.2 Product Overview......................................................... 3 1.3 Product Description...................................................... 4 1.3.1 Package Pinout ....................................................... 4 1.3.2 Block Organization................................................. 4 2 PRINCIPLES OF OPERATION........................................ 7 2.1 Data Protection............................................................. 8 3 BUS OPERATION ............................................................ 8 3.1 Read.............................................................................. ...
Page 5
... Bottom Boot Location Extended Cycling Capability Minimum 100,000 Block Erase Cycles SHARP’s LH28F160BJHE-BTLTH Flash memory is a high-density, low-cost, nonvolatile, read/write storage solution for a wide range of applications. LH28F160BJHE-BTLTH can operate at V capability realize battery life and suits for cellular phone application. ...
Page 6
... V off during read operation. CCW 1.2 Product Overview The LH28F160BJHE-BTLTH is a high-performance 16M- bit Boot Block Flash memory organized as 1M-word of 16 bits or 2M-byte of 8 bits. The 1M-word/2M-byte of data is arranged in two 4K-word/8K-byte boot blocks, six 4K- word/8K-byte parameter blocks and thirty-one 32K- word/64K-byte main blocks which are individually erasable, lockable and unlockable in-system ...
Page 7
... For example, changing data from "10111101" to "10111100" requires "11111110" programming. 1.3 Product Description supply CC 1.3.1 Package Pinout LH28F160BJHE-BTLTH Boot Block Flash memory is available in 48-lead TSOP package (see Figure 2). CCR 1.3.2 Block Organization , the I CMOS CC This product architecture providing system memory integration ...
Page 8
Output Buffer Y Input A -A Decoder -1 19 Buffer Address X Decoder Latch Address Counter Figure 1. Block Diagram ...
Page 9
... CCW may be connected to 12V±0.3V for a total of 80 hours maximum. DEVICE POWER SUPPLY: Do not float any power pins. With V V SUPPLY the flash memory are inhibited. Device operations at invalid V CC Characteristics) produce spurious results and should not be attempted. GND SUPPLY GROUND: Do not float any ground pins. ...
Page 10
... PRINCIPLES OF OPERATION The LH28F160BJHE-BTLTH flash memory includes an on-chip WSM to manage block erase, full chip erase, word/byte write and lock-bit configuration functions. It allows for: 100% TTL-level control inputs, fixed power supplies during block erase, full chip erase, word/byte write and lock-bit configuration, and minimal processor overhead with RAM-like interface timings ...
Page 11
... Refer to Table 5 for write protection alternatives. 3 BUS OPERATION The local CPU reads and writes flash memory in-system. All bus cycles to or from the flash memory conform to standard microprocessor bus cycles. 3.1 Read Information can be read from any block, identifier codes ...
Page 12
Read Identifier Codes The read identifier codes operation manufacturer code, device code, block lock configuration codes for each block and the permanent lock configuration code (see Figure 4). Using the manufacturer and device codes, the system CPU can automatically ...
Page 13
Mode Notes Read 8 Output Disable Standby Reset 4 Read Identifier Codes 8 Write 6,7,8 Mode Notes Read 8 Output Disable Standby Reset 4 Read Identifier Codes 8 Write 6,7,8 NOTES: 1. Refer to DC Characteristics. When ...
Page 14
Bus Cycles Command Req’d. Read Array/Reset ≥2 Read Identifier Codes Read Status Register Clear Status Register Block Erase Full Chip Erase Word/Byte Write Block Erase and Word/Byte Write Suspend Block Erase and Word/Byte Write Resume Set Block Lock-Bit Clear Block ...
Page 15
Read Array Command Upon initial device power-up and after exit from reset mode, the device defaults to read array mode. This operation is also initiated by writing the Read Array command. The device remains enabled for reads until another ...
Page 16
Block Erase Command Erase is executed one block at a time and initiated by a two-cycle command. A block erase setup is first written, followed by an block erase confirm. This command sequence requires appropriate sequencing and an address ...
Page 17
... The only other valid commands while block erase is suspended are Read Status Register and Block Erase Resume. After a Block Erase Resume command is written to the flash memory, the WSM will continue the block erase process. Status register bits SR.6 and SR.7 will automatically clear and RY/BY# will return to V ...
Page 18
Set Block and Permanent Lock-Bit Commands A flexible block locking and unlocking scheme is enabled via a combination of block lock-bits, a permanent lock-bit and WP# pin. The block lock-bits and WP# pin gates program and erase operations while ...
Page 19
... Block Locking by the WP# This Boot Block Flash memory architecture features two hardware-lockable boot blocks so that the kernel code for the system can be kept secure while other blocks are programmed or erased as necessary. The lockable two boot blocks are locked when WP#=V any program or erase operation to a locked block will ...
Page 20
WSMS BESS ECBLBS SR.7 = WRITE STATE MACHINE STATUS (WSMS Ready 0 = Busy SR.6 = BLOCK ERASE SUSPEND STATUS (BESS Block Erase Suspended 0 = Block Erase in Progress/Completed SR.5 = ERASE ...
Page 21
Start Write 70H Read Status Register 0 SR.7= 1 Write 20H Write D0H, Block Address Read Status Register No 0 Suspend SR.7= Block Erase Yes 1 Full Status Check if Desired Block Erase Complete FULL STATUS CHECK PROCEDURE Read Status ...
Page 22
Start Write 70H Read Status Register 0 SR.7= 1 Write 30H Write D0H Read Status Register 0 SR.7= 1 Full Status Check if Desired Full Chip Erase Complete FULL STATUS CHECK PROCEDURE Read Status Register Data(See Above Range ...
Page 23
Start Write 70H Read Status Register 0 SR.7= 1 Write 40H or 10H Write Word/Byte Data and Address Read Status Register Suspend Word/Byte No Suspend 0 SR.7= Word/Byte Yes Write 1 Full Status Check if Desired Word/Byte Write Complete FULL ...
Page 24
Start Write B0H Read Status Register 0 SR. SR.6= Block Erase Completed 1 Read or Word/Byte Write Read Word/Byte Write ? Read Array Data Word/Byte Write Loop No Done? Yes Write D0H Write FFH Read Array Data Block ...
Page 25
Start Write B0H Read Status Register 0 SR. Word/Byte Write Completed SR.2= 1 Write FFH Read Array Data Done No Reading Yes Write D0H Write FFH Word/Byte Write Resumed Read Array Data Figure 9. Word/Byte Write Suspend/Resume Flowchart ...
Page 26
Start Write 70H Read Status Register 0 SR.7= 1 Write 60H Write 01H/F1H, Block/Device Address Read Status Register 0 SR.7= 1 Full Status Check if Desired Set Lock-Bit Complete FULL STATUS CHECK PROCEDURE Read Status Register Data(See Above) 1 SR.3= ...
Page 27
Start Write 70H Read Status Register 0 SR.7= 1 Write 60H Write D0H Read Status Register 0 SR.7= 1 Full Status Check if Desired Clear Block Lock-Bits Complete FULL STATUS CHECK PROCEDURE Read Status Register Data(See Above) 1 SR.3= V ...
Page 28
... PC board trace inductance. 5.4 V Trace on Printed Circuit Boards CCW Updating flash memories that reside in the target system requires that the printed circuit board designer pay attention to the V CCW supplies the memory cell current for word/byte writing and block erasing ...
Page 29
... For the lockout voltage, refer to the specification. (See chapter 6.2.3.) 3) Data protection through RP# When the RP# is kept low during read mode, the flash memory will be reset mode, then write protecting all blocks. When the RP# is kept low during power up and ...
Page 30
ELECTRICAL SPECIFICATIONS 6.1 Absolute Maximum Ratings* Operating Temperature During Read, Block Erase, Full Chip Erase, Word/Byte Write and Lock-Bit Configuration .............-40°C to +85°C Storage Temperature During under Bias ............................... -40°C to +85°C During non Bias ................................ -65°C to +125°C ...
Page 31
AC INPUT/OUTPUT TEST CONDITIONS 2.7 INPUT 0.0 AC test inputs are driven at 2.7V for a Logic "1" and 0.0V for a Logic "0". Input timing begins, and output timing ends, at 1.35V. Input rise and fall times (10% ...
Page 32
DC CHARACTERISTICS Sym. Parameter I Input Load Current LI I Output Leakage Current Standby Current CCS Auto Power-Save Current CCAS Reset Power-Down Current CCD Read Current CCR ...
Page 33
Sym. Parameter V Input Low Voltage IL V Input High Voltage IH V Output Low Voltage OL V Output High Voltage OH1 (TTL) V Output High Voltage OH2 (CMOS Lockout during Normal CCWLK CCW Operations V V during ...
Page 34
AC CHARACTERISTICS - READ-ONLY OPERATIONS Sym. t Read Cycle Time AVAV t Address to Output Delay AVQV t CE# to Output Delay ELQV t RP# High to Output Delay PHQV t OE# to Output Delay GLQV t CE# to ...
Page 35
Standby Address Selection V IH ADDRESSES( CE#( OE#( WE#( HIGH Z DATA(D/Q) (DQ - PHQV V ...
Page 36
Standby Address Selection V IH ADDRESSES( CE#( OE#( BYTE#( HIGH Z DATA(D/Q) (DQ - HIGH Z DATA(D/Q) ...
Page 37
AC CHARACTERISTICS - WRITE OPERATIONS Sym. t Write Cycle Time AVAV t RP# High Recovery to WE# Going Low PHWL t CE# Setup to WE# Going Low ELWL t WE# Pulse Width WLWH t WP#V Setup to WE# Going ...
Page 38
V IH ADDRESSES( CE#( ELWL V IH OE#( WE#( High Z DATA(D/ BYTE#( High Z ("1") RY/BY#(R) (SR.7) V ...
Page 39
ALTERNATIVE CE#-CONTROLLED WRITES Sym. t Write Cycle Time AVAV t RP# High Recovery to CE# Going Low PHEL t WE# Setup to CE# Going Low WLEL t CE# Pulse Width ELEH t WP#V Setup to CE# Going High SHEH ...
Page 40
V IH ADDRESSES( CE#( OE#( WE#( High Z DATA(D/ BYTE#( High Z ("1") RY/BY#(R) (SR. ...
Page 41
RESET OPERATIONS High Z ("1") RY/BY#(R) (SR. ("0" RP#( High Z ("1") RY/BY#(R) (SR. ("0" RP#( (B)Reset During Block Erase, Full Chip Erase, Word/Byte Write or Lock-Bit ...
Page 42
BLOCK ERASE, FULL CHIP ERASE, WORD/BYTE WRITE AND LOCK-BIT CONFIGURATION PERFORMANCE Sym. Parameter t Word Write Time WHQV1 t EHQV1 Byte Write Time Block Write Time (In word mode) Block Write Time (In byte mode) t WHQV2 Block Erase ...
Page 43
...
Page 44
...
Page 45
...
Page 46
...
Page 47
...
Page 48
...
Page 49
...
Page 50
...
Page 51
...
Page 52
...
Page 53
A-1 RECOMMENDED OPERATING CONDITIONS A-1.1 At Device Power-Up AC timing illustrated in Figure A-1 is recommended for the supply voltages and the control signals at device power-up. If the timing in the figure is ignored, the device may not operate ...
Page 54
A-1.1.1 Rise and Fall Time Symbol t V Rise Time Input Signal Rise Time R t Input Signal Fall Time F NOTES: 1. Sampled, not 100% tested. 2. This specification is applied for not only the device ...
Page 55
A-1.2 Glitch Noises Do not input the glitch noises which are below V as shown in Figure A-2 (b). The acceptable glitch noises are illustrated in Figure A-2 (a). Input Signal V (Min (Max.) IL Input Signal (a) ...
Page 56
... A-2 RELATED DOCUMENT INFORMATION Document No. AP-001-SD-E Flash Memory Family Software Drivers AP-006-PT-E Data Protection Method of SHARP Flash Memory RP#, V AP-007-SW-E NOTE: 1. International customers should contact their local SHARP or distribution sales office. (1) Document Name Electric Potential Switching Circuit PP iv ...
Page 57
... Head Office: No. 360, Bashen Road, Xin Development Bldg. 22 Waigaoqiao Free Trade Zone Shanghai 200131 P.R. China Email: smc@china.global.sharp.co.jp EUROPE SHARP Microelectronics Europe Division of Sharp Electronics (Europe) GmbH Sonninstrasse 3 20097 Hamburg, Germany Phone: (49) 40-2376-2286 Fax: (49) 40-2376-2232 www.sharpsme.com SINGAPORE SHARP Electronics (Singapore) PTE., Ltd. ...