MAX3385EEAP Maxim Integrated Products, MAX3385EEAP Datasheet - Page 2

• Manufacturer Part Number: MAX3385EEAP
• Description: Dual Transmitter/Receiver RS-232 20-Pin SSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX3385EEAP

• Package: 20SSOP
• Data Transmission Topology: Point-to-Point
• Interface Standards: EIA/TIA-232|RS-232|V.24|V.28
• Data Rate: 0.25(Min) Mbps
• Function: Line Transmitter/Receiver
• Number Of Transceivers: 1
• Number Of Transmitters: 2
• Transmitter Signal Type: Single-Ended
• Transmitter Communication Type: RS-232
• Typical Single Supply Voltage: 3.3|5 V

ABSOLUTE MAXIMUM RATINGS
V
V+ to GND (Note 1) ..................................................-0.3V to +7V
V- to GND (Note 1) ...................................................+0.3V to -7V
V+ + |V-| (Note 1) .................................................................+13V
Input Voltages
Output Voltages
Short-Circuit Duration, T_OUT to GND.......................Continuous
±15kV ESD-Protected, 3.0V to 5.5V, Low-Power,
up to 250kbps, True RS-232 Transceiver
ELECTRICAL CHARACTERISTICS
(V
unless otherwise noted. Typical values are at T
2
Note 1: V+ and V- can have maximum magnitudes of 7V, but their absolute difference cannot exceed 13V.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
DC CHARACTERISTICS (V
Supply Current
Shutdown Supply Current
LOGIC INPUTS
Input Logic Threshold Low
Input Logic Threshold High
Transmitter Input Hysteresis
Input Leakage Current
RECEIVER OUTPUTS
Output Leakage Current
Output Voltage Low
Output Voltage High
RECEIVER INPUTS
Input Voltage Range
Input Threshold Low
Input Threshold High
Input Hysteresis
Input Resistance
CC
T_IN, SHDN to GND ..............................................-0.3V to +6V
R_IN to GND .....................................................................±25V
T_OUT to GND...............................................................±13.2V
R_OUT .....................................................-0.3V to (V
CC
_______________________________________________________________________________________
to GND ..............................................................-0.3V to +6V
= +3V to +5.5V, C1–C4 = 0.1µF, tested at 3.3V ±10%; C1 = 0.047µF, C2–C4 = 0.33µF, tested at 5.0V ±10%; T
PARAMETER
CC
= +3.3V or +5V, T
SHDN = V
SHDN = GND
T_IN, SHDN
T_IN, SHDN
T_IN, SHDN
R_OUT, receivers disabled
I
I
T
T
T
OUT
OUT
A
A
A
= +25°C
= +25°C
= +25°C
= 1.6mA
= -1.0mA
CC
A
, no load
= +25°C.)
A
= +25°C)
CC
+ 0.3V)
CONDITIONS
V
V
V
V
V
V
CC
CC
CC
CC
CC
CC
Continuous Power Dissipation (T
Operating Temperature Ranges
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
= 3.3V
= 5.0V
= 3.3V
= 5.0V
= 3.3V
= 5.0V
20-Pin SSOP (derate 8.00mW/°C above +70°C) ..........640mW
18-Pin SO (derate 9.52mW/°C above +70°C)...............762mW
MAX3385ECAP ....................................................0°C to +70°C
MAX3385ECWN ...................................................0°C to +70°C
MAX3385EEAP .................................................-40°C to +85°C
V
MIN
2.0
2.4
0.6
-25
0.6
0.8
CC
3
A
-
= +70°C)
±0.01
±0.05
V
TYP
0.3
0.5
0.1
1.2
1.5
1.5
1.8
0.5
CC
1
5
-
A
MAX
±10
+25
= T
0.8
0.4
2.4
2.4
±1
10
1
7
MIN
to T
UNITS
mA
µA
µA
µA
kΩ
V
V
V
V
V
V
V
V
V
MAX
,