ATV212W075N4 SQUARE D, ATV212W075N4 Datasheet - Page 5

• Manufacturer Part Number: ATV212W075N4
• Description: 52T3469
• Manufacturer: SQUARE D

Specifications of ATV212W075N4

• Supply Voltage Range: 380VAC To 480VAC
• No. Of Phases: 3
• Power Rating: 750W
• Rohs Compliant: Yes
• Output Current: 2.2A

Altivar 212 Inputs/Outputs Electrical Characteristics
Default
function setting
—
Fault relay
Speed attained
F: Run forward
R: Preset speed
at 15 Hz
RES: Reset
Output
frequency
—
Primary speed
reference,
0–10 V
Secondary
speed
reference,
1–10 V
—
—
Function
External power supply input
Internal supply
Common
Configurable relay outputs
Configurable logic inputs
Configurable analog output
Internal supply available
Configurable analog/
logic input
Configurable analog input
Graphic display terminal
or Modbus
Fieldbus
Terminals
PLC
P24
CC
FLA
FLB
FLC
RY
RC
F
R
RES
FM
PP
VIA
VIB
RJ45
Open style
connector
Characteristics
+24 Vdc input for external power supply for logic inputs Max. permissible voltage: 50 Vdc
Short-circuit and overload protection: 24 Vdc supply (min. 21 Vdc, max. 27 Vdc),
maximum current: 200 mA
0 Vdc common (2 terminals)
1 relay logic output, 1 N/C contact, and 1 N/O contact with common point
Minimum switching capacity: 10 mA for 5 Vdc
Maximum switching capacity:
• On resistive load (cos  = 1): 5 A for 250 Vac or 30 Vdc
• On inductive load (cos  = 0.4 and L/R = 7 ms): 2 A for 250 Vac or 30 Vdc
Max. response time: 10 ms
1 relay logic output, 1 N/O contact
Minimum switching capacity: 3 mA for 24 Vdc
Maximum switching capacity:
• On resistive load (cos  = 1): 3 A for 250 Vac or 30 Vdc
• On inductive load (cos  = 0.4 and L/R = 7 ms): 2 A for 250 Vac or 30 Vdc
Max. response time: 7 ms ± 0.5 ms
3 programmable logic inputs, 24 Vdc, compatible with level 1 PLC, IEC 65A-68 standard
Impedance: 4.7 kΩ
Maximum voltage: 30 Vdc
Max. sampling time: 2 ms ±0.5 ms
Multiple assignment makes it possible to configure several functions on one input
Positive logic (Source): State 0 if  5 Vdc or logic input not wired, state 1 if  11 Vdc
Negative logic (Sink): State 0 if  16 Vdc or logic input not wired, state 1 if  10 Vdc
1 switch-configurable (SW101) voltage or current analog output:
• Voltage analog output 0–10 Vdc, minimum load impedance 7.62 kΩ
• Current analog output X–Y mA by programming X and Y from 0 to 20 mA, maximum
load impedance: 970 Ω
Max. sampling time: 2 ms ±0.5 ms
Resolution: 10 bits
Accuracy: ±1 % for a temperature variation of 60° C
Linearity: ±0.2%
Short-circuit and overload protection: One 10.5 Vdc ± 5% supply for the reference
potentiometer (1 to 10 kΩ), maximum current: 10 mA
Switch-configurable voltage or current analog input:
• Voltage analog input 0–10 Vdc, impedance 30 kΩ maximum voltage: 24 Vdc
• Analog current input X–Y mA by programming X and Y from 0 to 20 mA, with
impedance 250 Ω
Max. sampling time: 3.5 ms ±0.5 ms
Resolution: 10 bits
Accuracy: ±0.6% for a temperature variation of 60° C
Linearity: ±0.15% of the maximum value
This analog input is also configurable as a logic input
Consult the Altivar 212 Programming Manual for more information
Voltage analog input, configurable as an analog input or as a PTC probe input
Voltage analog input:
• 0–10 Vdc, impedance 30 kΩ max. voltage 24 Vdc
• Max. sampling time: 22 ms ±0.5 ms
• Resolution: 10 bits
• Accuracy: ±0.6% for a temperature variation of 60 °C
• Linearity: ±0.15% of the maximum value PTC probe input:
• 6 probes max. mounted in series
• Nominal value < 1.5 kΩ
• Trip resistance 3 kΩ, reset value 1.8 kΩ
• Short-circuit detection threshold < 50 Ω
Used to connect graphic display terminal or connect the drive to a Modbus fieldbus
Note: for using Modbus on the RJ45, modify parameter F807 (see Modbus manual)
Refer to communication manual related to the fieldbus
5