V15W11-EZ200-W3 Honeywell Sensing and Control, V15W11-EZ200-W3 Datasheet

V15W11-EZ200-W3

Manufacturer Part Number

V15W11-EZ200-W3

Description

SWITCH SNAP SPDT 10A 125V

Manufacturer

Honeywell Sensing and Control

Series

V15Wr

Datasheets

1.V15W11-DZ200A02-W2.pdf (6 pages)

2.V15W11-DZ200A02-W2.pdf (2 pages)

Specifications of V15W11-EZ200-W3

Mfg Application Notes

Watertight Switches Transportation Applications

Circuit

SPDT

Switch Function

On-Mom

Contact Rating @ Voltage

10A @ 125VAC

Actuator Type

Round (Pin Plunger)

Mounting Type

Chassis Mount

Termination Style

Quick Connect - .187" (4.7mm)

Operating Force

200gf

Lead Free Status / Rohs Status

Lead free / RoHS Compliant

Other names

480-3752

Current page: 1 of 2
Download datasheet (100Kb)

Installation Instructions for the

MICRO SWITCH™ V-Basic Standard V15W

Watertight Switches

PERSONAL INJURY

• DO NOT USE these products as safety or emergency

Failure to comply with these instructions could result

in death or serious injury.

GENERAL INFORMATION

MICRO SWITCH™ V-Basic Standard V15W Watertight

switches are precision snap-action contact mechanisms

enclosed in watertight plastic cases. Switch actuation

triggers the mechanical closure of the switch’s contacts.

A small amount of arcing between the contacts during

contact closure occurs during normal operation. In order

to obtain desired switch performance, the switch must be

chosen based on the mechanical, electrical and

environmental conditions of the application.

Do not use this product in water. Although molded lead

wire versions carry an ingress protection rating of IP67

according to the test conditions of IEC 529, this test is to

check the ingress of water into the switch enclosure after

submerging the switch in water for a given time.

Sensing and Control

CAUTION

SWITCH DAMAGE

• Wiring must be rated to meet or exceed circuitry

• Connecting circuitry must not exceed switch rating.

• Wiring connections must be properly secured.

• Do not exceed recommended soldering time or

• Do not contact switch housing with soldering device.

• Do not exceed recommended mounting screw tightening

• Discontinue use if switch has been damaged or cover

• Do not apply side loads to actuator or exceed specified

• Do not operate or store in areas where corrosive gases

Failure to comply with these instructions may result

in product and/or property damage.

IMPROPER USE

Failure to comply with these instructions will result in

death or serious injury.

• Do not use in hazardous environments where

requirements.

temperature.

torques.

removed.

travel limits.

such as hydrogen sulfide are present.

stop devices or in any other application where failure of

the product could result in personal injury.

flammable or explosive gases or liquids such as

gasoline or thinners, etc., are present.

WARNING

Satisfying this test condition does not mean that the

switch can be used in water. Switches with terminals are

also sealed, but because the terminals are exposed the

corresponding degree of protection is IP00.

MOUNTING INFORMATION

*To prevent loosening of screws, use spring washers

• Turn OFF the power supply before mounting or removing

• Mount the switch onto a flat surface. Mounting on an

• Use an operating device with low frictional resistance

• Position the operating device perpendicular to the

• Position the operating device so that no force is applied

• The operating device should be positioned so that when

• The operating device should never force the

WIRING INFORMATION – TERMINAL VERSIONS

• Connect wires firmly to terminals.

• Replace wires that have damaged insulation.

• Use properly sized spade terminals.

• Use wire rated for the application’s electrical load and

• Provide strain relief when a potential exists for forces to

under screw heads and thread lock adhesive.

Mounting

hole size

3,1 mm

2,9 mm

(-K option)

the switch, wiring, or performing maintenance or

inspection. Failure to do so may result in electric shock.

uneven surface may cause deformation of the switch,

resulting in faulty operation or damage.

and of a shape that will not interfere with the plunger seal

otherwise the plunger may be damaged or the sealing

may deteriorate.

actuator/pushbutton to prevent side loading of the switch

actuator or pushbutton.

to the pushbutton/actuator when the switch is in the free

position.

the switch is in the operating position it should move the

actuator no less than 70% of the total travel. Setting the

travel position so that less than 70% of the total travel is

used may cause poor contact or welding conditions due

to an insufficient contact switching force.

actuator/pushbutton to exceed the total travel position.

application’s temperature

be transferred from the lead wires to the switch terminals

Flat fillister

Screw

Type*

Flat fillister

head

Screw

Size

3 mm

50066512

Tightening

Torque (max.)

5,8 kg-cm

[5.0 in-lb]

5,8 kg-cm

[5.0 in-lb]

ISSUE 1

Related parts for V15W11-EZ200-W3

V15W11-EZ200-W3 Summary of contents

Page 1

... Sensing and Control 50066512 Satisfying this test condition does not mean that the switch can be used in water. Switches with terminals are also sealed, but because the terminals are exposed the corresponding degree of protection is IP00. MOUNTING INFORMATION ...

Page 2

... MICRO SWITCH™ V-Basic Standard V15W Watertight Switches • The switch is sealed around the terminals. However, live terminals should never be exposed to water. Use appropriate sealed connectors or mount the switch in a sealed enclosure so that the terminals are not exposed to water. WIRING INFORMATION - PRE-LEADED VERSIONS • ...

Related keywords

V15W11-EZ200-W3 datasheet
V15W11-EZ200-W3 data sheet
V15W11-EZ200-W3 pdf datasheet
V15W11-EZ200-W3 component
V15W11-EZ200-W3 part
V15W11-EZ200-W3 distributor
V15W11-EZ200-W3 RoHS
V15W11-EZ200-W3 datasheet download