PS21564 MITSUBISHI, PS21564 Datasheet
PS21564
Available stocks
Related parts for PS21564
PS21564 Summary of contents
Page 1
... B-B Note order to get enough creepage distance between the terminals, please take some countermeasure such as a slit on PCB Treat the terminal V of PS21564-P as NC. (just the same as DIP-IPM ver.2) However, external connection nals is necessary for PS21562-P or PS21563-P. INTEGRATED POWER FUNCTIONS ...
Page 2
... When the sensed shunt voltage exceeds the SC trip-level, all the L-side IGBTs are turned OFF and a fault signal (Fo) is output. Since the SC fault may be repetitive recommended to stop the system when the Fo signal is received and check the fault Collector current waveform 0 2 PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE C2 (Note 8) C1 (Note 6) Protection circuit (UV) DIP-IPM H-side IGBT S U ...
Page 3
... C, non-repetitive, less than 60Hz, Sinusoidal, 1 minute, All connected pins to heat-sink plate Control Terminals FWDi Chip 18mm 16mm Groove Power Terminals PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE Ratings 450 500 600 15 30 22.2 (Note 1) –20~+125 100 C) however, to en- f 125 100 C). ...
Page 4
... Trip level Reset level T 125 C j Trip level Reset level C = 22nF FO Applied between according to the following approximate equation : C FO PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — — — — Limits Min. Typ. Max. — 1. 1.45 — 2.05 1.55 = 125 C — ...
Page 5
... C T 100 C, f N-line wiring inductance less than Between 1.7 times and 10nH 2.0 times of rated current (Note 9) Between V -N (including surge) NC PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE Limits Min. Typ. Max. — 0.59 0.98 — — 20 — ...
Page 6
... HVIC1 IGBT1 Di1 COM S HVIC2 V V IGBT2 Di2 COM S HVIC3 V V IGBT3 Di3 COM V S IGBT4 LVIC Di4 U OUT V CC IGBT5 Di5 V OUT U N IGBT6 Di6 OUT CIN GND CFO CFO CIN PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM (NC) NO Sep. 2005 ...
Page 7
... Protection circuit state Control supply voltage V Output current Ic Error output Fo signal is set by the external capacitor SET RESET reference voltage CR circuit time constant DELAY the circuits start to operate when next input is applied. Dr RESET SET PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE . FO RESET b6 b7 Sep. 2005 ...
Page 8
... DBt line 10k (min) pull-down resistor. Therefore, when using an external Wiring inductance should be less than 10nH. Equivalent to the inductance of a copper pattern with length=17mm, width=3mm, and thickness=100 m N Shunt resistor PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE RESET c5 c6 DIP-IPM , (Logic) Please make the GND wiring connection ...
Page 9
... CC V OUT OUT CIN V NC GND CFO CIN CFO C4 this wiring is too long, the SC level fluctuation might be larger and cause SC malfunction. PS21564-P TRANSFER-MOLD TYPE INSULATED TYPE DIP-IPM Too long wiring here might cause short-circuit Shunt resistor N1 terminals (C ). (Example : Sep. 2005 t FO ...