CX099 Sony, CX099 Datasheet
Related parts for CX099
CX099 Summary of contents
Page 1
... Progressive Scan CCD Image Sensor with Square Pixel for B/W Cameras For the availability of this product, please contact the sales office. Description The ICX099AL is a 1/2-inch optical interline CCD solid-state image sensor with a square pixel array and 800K effective pixels. Progressive scan allows all pixels' signals to be output independently within approximately 1/15 second ...
Page 2
... Reset gate clock H Horizontal register transfer clock 1 H Horizontal register transfer clock 2 Ratings Unit –40 to +10 V –50 to +15 V –50 to +0.3 V –40 to +0.3 V – –0.3 to +18 V –10 to +18 V – –0.3 to +28 V –0 +15 V – –13 to +13 V –30 to +80 °C –10 to +60 °C ICX099AL Remarks 2 ...
Page 3
... V RGL RGLm 19.75 20.5 SUB – 3 – Max. Unit Remarks 15. Max. Unit Remarks mA Waveform Max. Unit diagram 15 – High-level coupling 1 High-level coupling 0 Low-level coupling 0 Low-level coupling Low-level coupling 0 Low-level coupling 21. ICX099AL L Remarks = V VH02A = (V +V )/2 VL1 VL3 ...
Page 4
... V2A V2B V12A V2B1 V2A3 V32B C V13 SUB GND V12A V2A C V2A3 C V13 GND V32B V 3 Horizontal transfer clock equivalent circuit – 4 – Min. Typ. Max. Unit 2200 1800 6800 1200 1000 1500 56 120 10 400 ICX099AL Remarks Ω Ω Ω kΩ ...
Page 5
... VHH V VHL V VLH V VL1 V VLL V VH2A V VHH V VHL V VLH VL2A VL2B V VLL V VH3 V VHL V VLH V VLL VH02A VL01 VL03 VL3 VL03 – 5 – and VH2B VHH – VH1 VL01 – V V2A VH02A VL2A – V V2B VH02B VL2B – VH3 VL03 ICX099AL ...
Page 6
... H 1 twh tf V RGH V RG Point A is the minimum value of the coupling waveform during the period from RGLL )/2 RGLm 100% 90% V SUB 10 twh – 6 – twl and H waveforms and H is two twl is the average value of V RGL . ICX099AL RGL and RGLH ...
Page 7
... Symbol Unit Min. Typ. Max 500 600 700 Wave Length [nm] – 7 – Unit 0.5 0.5 15 350 0.01 0.01 0.01 0. 0.5 0.5 rising side of the H and H waveforms must Remarks 800 900 ICX099AL Remarks During µs readout µs ns During µs drain charge 1000 ...
Page 8
... H 8 779 (V) Zone Zone II, II' Ignored region Effective pixel region S/H AMP Signal output [ B] – 8 – Unit Measurement method Remarks mV 1 1/30s accumulation mode 60° 1/15s accumulation mode % 4 Zone 0 and % 4 Zone 60° 60° ICX099AL (Ta = 25°C) I ...
Page 9
... High-speed mode The signals for all effective areas are output in approximately 1/30s by repeating readout pixels and non- readout pixels every two lines. The vertical resolution is approximately 380TV-lines. This readout mode emphasizes processing speed over vertical resolution. High-speed mode OUT – 9 – ICX099AL ...
Page 10
... Measure the average value of the signal output (Vdt [mV]) with the device ambient temperature 60°C and the device in the light-obstructed state, using the horizontal idle transfer level as a reference color temperature of 3200K halogen source subject the center of the screen, and substitute the value into the S 1 100 [%] (1/10V method conversion value) 10 100 [%] – 10 – ICX099AL ...
Page 11
... Adjust the signal output value generated by strobe light to 150mV. After setting the strobe light so that it strobes with the following timing, measure the residual signal (Vlag). Substitute the value into the following formula. Lag = (Vlag/150) 100 [%] VD V2A Strobe light timing Output Light Signal output 150mV Vlag (Lag) – 11 – ICX099AL ...
Page 12
... ICX099AL ...
Page 13
... Sensor Readout Clock Timing Chart XV1 XV2A XV2B XV3 XSG1 XSG2 HD 42.2µs (604 bits) V1 V2A V2B V3 Progressive Scan Mode Sensor readout clocks XSG1 and XSG2 are used by composing XV2A and XV2B. 69.8ns (1 bit) 2.51µs (36 bits) – 13 – ICX099AL ...
Page 14
... Sensor Readout Clock Timing Chart XV1 XV2A XV2B XV3 XSG1 XSG2 HD 42.2µs (604 bits) V1 V2A V2B V3 High-speed Mode Sensor readout clock XSG1 is used by composing XV2A. 69.8ns (1 bit) 2.51µs (36 bits) – 14 – ICX099AL ...
Page 15
... ICX099AL ...
Page 16
... ICX099AL ...
Page 17
... ICX099AL ...
Page 18
... ICX099AL ...
Page 19
... If a load is applied to the entire surface by a hard component, bending stress may be generated and the package may fracture, etc., depending on the flatness of the ceramic portions. Therefore, for installation, use either an elastic load, such as a spring plate adhesive. 29N Low melting point glass Shearing strength – 19 – 29N Tensile strength Torsional strength ICX099AL 0.9Nm ...
Page 20
... Do not expose to strong light (sun rays) for long periods. For continuous using under cruel condition exceeding the normal using condition, consult our company. b) Exposure to high temperature or humidity will affect the characteristics. Accordingly avoid storage or usage in such conditions. – 20 – ICX099AL ...
Page 21
... ICX099AL ...