LT1260CN Linear Technology Corporation, LT1260CN Datasheet
LT1260CN
Available stocks
Related parts for LT1260CN
LT1260CN Summary of contents
Page 1
... RGB MUX and cable driver. These amplifiers turn on in only 100ns and turn off in 40ns, making them ideal in spread spectrum and portable equipment applications. The LT1259/LT1260 amplifiers are manufactured on Linear Technology’s proprietary complementary bipolar process. , LTC and LT are registered trademarks of Linear Technology Corporation CABLE V OUT 75 ...
Page 2
... EN pins = 0V, pulse tested, unless otherwise noted. S CONDITIONS 1kHz 1k 1kHz f = 1kHz V = 13V 15V 3V Enabled Disabled Disabled V = 15V 5V ORDER PART NUMBER OUT R + LT1260CN 14 V LT1260CS LT1260IN 12 OUT G – LT1260IS OUT PACKAGE 16-LEAD PLASTIC SOIC = 70 C/W ( 100 C/W (S) JA MIN TYP MAX 0 120 3.6 1 4 ...
Page 3
ELECTRICAL C HARA TERISTICS each amplifier SYMBOL PARAMETER V Maximum Output Voltage Swing OUT CMRR Common-Mode Rejection Ratio Inverting Input Current Common-Mode Rejection PSRR Power Supply Rejection ...
Page 4
... are available on special request. Consult factory. Note 3: Ground pins are not internally connected. For best performance, connect to ground. Note calculated from the ambient temperature T J power dissipation P according to the following formulas: D LT1259CN/LT1259IN • LT1259CS/LT1259IS • 110 C/ LT1260CNLT1260IN • LT1260CS/LT1260IS • 100 C/ TYPICAL AC PERFOR ( ...
Page 5
W U TYPICAL PERFOR A CE CHARACTERISTICS 5V Frequency Response PHASE GAIN ± 150 1. ...
Page 6
LT1259/LT1260 W U TYPICAL PERFOR A CE CHARACTERISTICS Output Impedance in Shutdown vs Frequency 100 V = ± 1. 0.1 100k 1M 10M 100M FREQUENCY (Hz) LT1259/60 • TPC11 Output ...
Page 7
PLIFIED SCHE ATIC APPLICATIO S I FOR ATIO Feedback Resistor Selection The small-signal bandwidth of the LT1259/ LT1260 are set by the external feedback resistors and the internal junction capacitors result, the ...
Page 8
LT1259/LT1260 U U APPLICATIO S I FOR ATIO The input slew rate of the LT1259/LT1260 is approxi- mately 270V/ s and is set by internal currents and capaci- tances. The output slew rate is set by the value of the ...
Page 9
U U APPLICATIO S I FOR ATIO Amplifier Disable Time 150 110 Differential Input Signal Swing The differential input swing is ...
Page 10
LT1259/LT1260 U TYPICAL APPLICATIO S 4. Capacitors C1 and C6 are optional and only needed to reduce overshoot when are activated with a long inductive ground wire. 5. The R, G and B amplifiers have ...
Page 11
... FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. ...
Page 12
... Slew Rate, Shutdown Mode Single, Dual and Quad Current Feedback Amplifiers R13 75 V RED OUT 75 V GREEN OUT 75 V BLUE OUT + R16 75 R17 75 R18 75 LT1259/60 • TA08 125960fas, sn125960 LT/TP 1197 REV A 4K • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 1993 ...