M63000SP Mitsumi Electronics, Corp., M63000SP Datasheet

no-image

M63000SP

Manufacturer Part Number
M63000SP
Description
Manufacturer
Mitsumi Electronics, Corp.
Datasheet
DESCRIPTION
The M63000SP is a semiconductor IC developed as the motor
driver used to CD Player,CD-ROM.
This circuit includes Standby circuit,TSD circuit and 4-Channel
BTL Driver that is able to drive four actuators with one IC.
FEATURES
APPLICATION
CD Player,CD-ROM,Video-CD
BLOCK DIAGRAM
Vctl1(+)
VM1(+)
VM1(-)
Vctl2(+)
Low Output saturation voltage (typ:1.35V,at 0.5A)
Large Operating supply voltage range(4.5–15V)
Minimum Crossover distortion
VM2(+)
VM2(-)
15
13
14
5
4
3
+
-
+
-
+
10K
10K
+
-
-
5K
+
+
-
-
CH1
CH2
5K
Vref- out
2
Standby
36
+
-
37K
Vref - in
1
35K
Standby
SS.GND
Function
1–4 ch
35
Vcc
17
+
-
Vcc
20
PIN CONFIGURATION (TOP VIEW)
10K
10K
TSD
1.23V
4-CHANNEL ACTUATOR MOTOR DRIVER
PGND ( 8PIN)
MITSUBISHI <CONTROL / DRIVER IC>
6–12, 25–31
GND
Reg-base
Vref - out
Reg-Vref
Regbase
+
-
Vref - in
Vctl1(+)
Vctl2(+)
VM1(+)
VM2(+)
VM2(-)
VM1(-)
Vcc
18
10
11
14
16
17
18
12
13
15
Reg-Vref
1
2
3
4
5
6
8
9
7
16
Outline 36P4E
CH3
CH4
5K
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
20
19
M63000SP
+
-
+
-
Standby
SS . GND
Vctl4(+)
VM4(-)
VM4(+)
VM3(+)
VM3(-)
Vctl3(out)
Vctl3(-)
Vcc
Vctl3(+)
10K
+
GND
-
+
-
+
+
-
-
19 Vctl3(+)
34
32
21
22
24
33
23
Vctl4(+)
VM4(+)
VM4(-)
Vctl3(-)
Vctl3
VM3(+)
VM3(-)
out

Related parts for M63000SP

M63000SP Summary of contents

Page 1

... DESCRIPTION The M63000SP is a semiconductor IC developed as the motor driver used to CD Player,CD-ROM. This circuit includes Standby circuit,TSD circuit and 4-Channel BTL Driver that is able to drive four actuators with one IC. FEATURES Low Output saturation voltage (typ:1.35V,at 0.5A) Large Operating supply voltage range(4.5–15V) ...

Page 2

... With infinite heatsink Limits Min. Typ. 4.5 (Ta=25˚C,Vcc=9V unless otherwise noted.) Test conditions M63000SP Function CH3 amp. non-inverted input terminal Power supply CH3 amp. inverted input terminal CH3 input amp. output terminal CH3 amp. inverted output terminal CH3 amp. non-inverted output terminal GND CH4 amp ...

Page 3

... Tj when this device is used over Tj 150˚C. Therefore, this device must function under Tj maximum 150˚C condition. SHORT PROTECT M63000SP has an internal short protect circuit . It can proof between any output to Vcc or GND and each output to other output with under Vcc 13.2V condition. THE TIMING CHART Please start M63000SP with the following timing chart ...

Page 4

... Each of the Master-Amp.(VM+) and Slave Amp.(VM-) have the gain of 2.66 and the output voltage is about (Vcc-0.7)/2. Vref + + VM+ Vctl VM- Vctl- Vctlout Input Amp. (sets gain externally) CH3Amp.(uses input Amp.as a Buffer Amp.) Vref (2.5V) VM- (Vcc-0.7)/2 M63000SP Output of non-inverted Amp. (Gain=2.66) + VM+ CH3 + VM- Output of inverted Amp. (Gain=2.66) Vctl+ 1V VM+ VM- 2.66V 2.66V 5.32V = Gain 1 ...

Page 5

... Bottom side saturation voltage 400 500 600 700 (mA) Load current (deg) 180 PHASE 90 0 -90 -180 100 300 600 At mounted on a board Without heatsink 100 125 150 M63000SP Used board Size:174 X 140mm Thickness:1.5mm Paper Phenol on both sides ...

Page 6

... Vctl3(out 10K Vctl3(-) + Vcc 10K + + OP1 - 10K - 1.23V M63000SP Standby 37K 36 35K 35 SS.GND 34 Vctl4(+) VM4(-) 33 VM4(+) 32 Tracking Spindle VM3(+) 24 M VM3(-) 23 0.022uF 22 560K pwm2 82K 21 20 Vcc 0.022uF 19 560K Vctl3(+) ...

Related keywords