BD8152FVM Rohm, BD8152FVM Datasheet
BD8152FVM
Available stocks
Related parts for BD8152FVM
BD8152FVM Summary of contents
Page 1
... TFT-LCD panel is suppressed. Features 1) Current mode PWM system 2) Input voltage is 2 5.5 V (BD8152FVM), 2 5.5 V (BD8158FVM, providing the low power input) 3) Switching frequency is variable as 600 kHz/1,200 kHz. 4) Built-in 0.25 Ω power switch 5) Feedback voltage 1.245 ± 1% ...
Page 2
... Parameter Power supply voltage (BD8152FVM) Power supply voltage (BD8158FVM) Switch current Switch pin voltage *Specified at 600kHz switching operating. Electrical Characteristics BD8152FVM (Unless otherwise specified 25°C; Vcc = 3.3 V; ENB = 3.3 V) Parameter [triangular waveform oscillator] Oscillating frequency 1 Oscillating frequency 2 [Overcurrent protection circuit] Overcurrent limit ...
Page 3
Electrical Characteristics BD8158FVM (Unless otherwise specified 25°C; Vcc = 2.5 V; ENB = 2.5 V) Parameter [triangular waveform oscillator] Oscillating frequency 1 Oscillating frequency 2 [Overcurrent protection circuit] Overcurrent limit [Soft start circuit] SS source current [Under-voltage lockout ...
Page 4
Reference Data (Unless otherwise specified 25°C) 2.00 1.75 1.50 1.25 -40°C 1.00 0.75 25°C 0.50 125°C 0.25 0. SUPPLY VOLTAGE:Vcc [V] Fig. 1 Total Supply Current -12 -16 -20 0 ...
Page 5
... Fig. 14 Max. Load Current vs Power Supply Voltage 9 Vcc = 2.5 V 8.8 8.6 8.4 8.2 BD8158FVM 8 0.0 0.1 1.0 LOAD CURRENT:Io[A] Fig. 17 Output Voltage Load Regulation 1 5/ BD8152FVM 50 0.05 0.15 0.25 0.35 0.45 OUTPUT CURRENT:Io[A] Fig. 12 Vcc = 5V Power Efficiency Io = 100 100 mV Fig. 15 Load Response Waveform 9 8.8 Vcc=5V 8.6 8.4 8.2 BD8152FVM 8 0.0 0.1 1.0 LOAD CURRENT:Io[A] Fig. 18 Output Voltage Load Regulation 2 ...
Page 6
Block Diagram Pin Assignment Diagram and Function Pin No. Pin name 1 COMP Error amp output pin 2 FB Error amp inversion input pin 3 ENB Control input pin 4 GND Ground pin 5 SW N-channel power FET drain output ...
Page 7
... This block generates the internal reference voltage of 1.245 V (Typ.). • Protection circuit (UVLO/TSD) UVLO (under-voltage lockout protection circuit) shuts down the circuits when the voltage is 2.2 V (TYP.BD8152FVM),1.8 V (TYP.BD8158FVM) or lower. Thermal shutdown circuit shuts down IC at 175°C (Typ.) and recovers at 160°C (Typ.). ...
Page 8
Timing Chart Startup sequence VCC ENB Overcurrent protection operating 2.5V VCC,ENB Fig. 21 Startup Sequence Waveform Fig. 22 Overcurrent Protection Operating Waveform 8/16 ...
Page 9
... Set with sufficient margin because the coil L value may have the dispersion of approx. ±30%. If the coil current exceeds the rating current I BD8152FVM / BD8158FVM use the current mode DC/DC converter control and has the optimized design at the coil value. The following coil values are recommended from the aspects of power efficiency, response and safety. When the coil out of this range is selected, the stable continual operation is not guaranteed such as the switching waveform becomes irregular ...
Page 10
Selecting the output rectification diode Schottky barrier diode is recommended as the rectification diode to use at the DC/DC converter output stage. Select the diode paying attention to the max. inductor current and max. output voltage. Max. Inductor current ...
Page 11
Setting the phase compensation circuit the current mode control, since the coil current is controlled, a pole (phase lag) made by the CR filter composed of the output capacitor and load resistor ...
Page 12
... Application Examples * Although ROHM is sure that the application examples are recommendable ones, further check the characteristics of components that require high precision before using them. When a circuit is used modifying the externally connected circuit constant, be sure to decide allowing sufficient margins considering the dispersion of values by external parts as well as our IC including not only the static but also the transient characteristic ...
Page 13
... Application Examples (3) When the circuit is intended to operate at the lower voltage than the IC operating range: Although the recommended operating range of IC starts from 2 2.1 V (BD8152FVM / BD8158FVM possible to continue operating by composing the self-energizing type step-up DC/DC converter application even if the input voltage lowered than 2.1 V. This example is recommended for the application with battery input. ...
Page 14
Application Examples (5) When the Supply Voltage is over 4.0 V (BD8158FVM only) The Capacitor C4 is inserted to COMP pin, and it operates when the Supply Voltage is over 4 this case, Switching Frequency is limited to ...
Page 15
Operation Notes 1) Absolute maximum ratings Use of the IC in excess of absolute maximum ratings such as the applied voltage or operating temperature range may result in IC damage. Assumptions should not be made regarding the state of the ...
Page 16
... M 0.65 0. 70×70×1.6mm Board BD8158FVM BD8152FVM 100 AMBIENT TEMPERATURE[ ℃ ] Fig. 36 Power Dissipation Reduction Package MSOP8 Package MSOP8 <Tape and Reel information> Tape Embossed carrier tape Quantity ...
Page 17
... ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog ...