PAN301ASI-204 ETC-unknow, PAN301ASI-204 Datasheet

Page 1

... Power saving mode during times of no movement Serial Interface for programming and data transfer I/O pin 5.0 volt tolerance Ordering Information Order number PAN301ASI-204 PAN301ASI-208 All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission. PixArt Imaging Inc. E-mail: fae_service@pixart.com.tw ...

Page 2

PixArt Imaging Inc. PAN301A 1. Pin Description Pin No. Name 1 VSS_LED 2 LED 3 OSCOUT 4 OSCIN VSS 7 VSS 8 VDD 9 VREFA 10 VREFB ...

Page 3

PixArt Imaging Inc. PAN301A 2. Block Diagram and Operation LED VSS_LED XA QUADRATURE XB OUTPUTS YA YB SCLK SERIAL INTERFACE INTERFACE SDIO Figure 3. Block diagram The PAN301A is a high performance CMOS-process optical mouse sensor with DSP integration chip ...

Page 4

PixArt Imaging Inc. PAN301A 3. Registers and Operation The PAN301A can be programmed through registers, via the serial port, and DSP configuration and motion data can be read from these registers. All registers not listed are reserved, and should never ...

Page 5

... No overflow (Default Overflow has occurred Motion Delta X overflow, ∆X buffer has overflowed since last report DXOVF overflow (Default Overflow has occurred Resolution in counts per inch 0 = 800 (Default @ PAN301ASI-208) RES[2: 400 (Default @ PAN301ASI-204 600 Reserved Reserved for future 0x03 Bit 7 6 Field ...

Page 6

PixArt Imaging Inc. PAN301A 0x05 Bit 7 6 Field LEDsht_enh XY_enh Usage Register 0x05 allows the user to change the operation of the sensor. Shown below are the bits, their default values, and optional values. Operation_Mode[4:0] “0xxxx”=Disable sleep mode “10xxx”=Enable ...

Page 7

... Normal operation (Default Power down mode Output resolution setting 0 = 800 (Default @ PAN301ASI-208) RES[2: 400 (Default @ PAN301ASI-204 600 Reserved Reserved for future All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission PixArt Imaging Inc. ...

Page 8

PixArt Imaging Inc. PAN301A 4. Specifications Absolute Maximum Ratings Symbol Parameter T Storage temperature STG TA Operating Temperature Lead Solder Temp V DC supply voltage DD ESD V DC input voltage IN Recommend Operating Condition Symbol Parameter Operating T A ...

Page 9

PixArt Imaging Inc. PAN301A Package Lid Lens Z Figure 4. Distance from Lens Reference Plane to Surface +X +Y Figure 5. 2D assembly All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to ...

Page 10

PixArt Imaging Inc. PAN301A AC Operating Condition Electrical Characteristics over recommended operating conditions. Typical values at 25 °C, V Symbol Parameter t Power Down Pulse Width PDW t PD Pulse Register PDR t Power Up from PD↓ ...

Page 11

PixArt Imaging Inc. PAN301A DC Electrical Characteristics Electrical Characteristics over recommended operating conditions. Typical values at 25 °C, V Symbol Parameter Type: PWR Supply Current I DD Mouse moving (Normal) Supply Current I DD Mouse not moving (sleep1) Supply Current ...

Page 12

PixArt Imaging Inc. PAN301A 5. Quadrature Mode The quadrature state of the PAN301A tells mouse controller which direction the mouse is moving in. The output format is two channels quadrature (X and Y direction), which emulates encoder phototransistors. The DSP ...

Page 13

PixArt Imaging Inc. PAN301A 5.2 Quadrature Output State Machine The following state machine shows the states of the quadrature output pins. The three things to note are that state 0 is entered after a power on reset. While the PD ...

Page 14

PixArt Imaging Inc. PAN301A 6. Serial Interface The synchronous serial port is used to set and read parameters in the PAN301A, and can be used to read out the motion information instead of the quadrature data pins. SCLK: The serial ...

Page 15

PixArt Imaging Inc. PAN301A edges of SCLK and read on every rising edge of SCLK. The micro-controller must high Z state after the last address data bit. The PAN301A will go to the high Z state after ...

Page 16

PixArt Imaging Inc. PAN301A The PAN301A will not write to any register and will reset the serial port (but nothing else) and be prepared for the beginning of future transmissions after PD goes low. 6.2.2 Firmware Flaws Error, or Others ...

Page 17

PixArt Imaging Inc. PAN301A SCLK t RESYNC 1us, min SDIO Figure 14. Re-synchronous serial interface using watchdog timer timeout 6.5 Power Down Mode There are two different ways to entry power down mode, using the PD line or register setting. ...

Page 18

PixArt Imaging Inc. PAN301A 6.5.2 Register Power Down Mode PAN301A can be placed in a power-down mode by setting bit 3 in the configuration register via a serial port write operation. After setting the configuration register, wait at least 1frame ...

Page 19

... PAN301ASI-20X 0.1uF 0.1uF Figure 18. Application circuit using serial interface with PAN301ASI-20X Figure 19. Example printed circuit board layout. (PAN301ASI-20X V.S CY7C63723-PC) All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission PixArt Imaging Inc. E-mail: fae_service@pixart ...

Page 20

... PAN301ASI-20X 0.1uF 0.1uF Figure 20. Application circuit using quadrature output with PAN301ASI-20X Figure 21. Example printed circuit board layout. (PAN301ASI-20X V.S CY7C63723-PC) All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission PixArt Imaging Inc. E-mail: fae_service@pixart ...

Page 21

... PAN301ASI-20X 0.1uF 0.1uF Figure 22. Application circuit using quadrature output with PAN301ASI-20X Figure 23. Example printed circuit board layout. (PAN301ASI-20X V.S EM84510FP) All rights strictly reserved any portion in this paper shall not be reproduced, copied or transformed to any other forms without permission PixArt Imaging Inc. E-mail: fae_service@pixart ...

Page 22

PixArt Imaging Inc. PAN301A 7.4 PCB Layout Consideration 1. Caps for pins MUST have trace lengths LESS than 5mm. 2. The trace lengths of OSCOUT, OSCIN must less than 6mm. 7.5 Recommended Value for R1 Radiometric intensity ...

Page 23

PixArt Imaging Inc. PAN301A 8. Package Information 8.1 Package Outline Drawing 19.30 0.760 0.457 0.018 13.589 0.535 11.938 0.470 ...

Page 24

PixArt Imaging Inc. PAN301A 8.2 Recommended PCB Mechanical Cutouts and Spacing 10.998 6.985 0.433 0.275 4.445 0.175 4.445 0.175 6.985 0.275 Figure 25. Recommended PCB mechanical cutouts and spacing 9. Update History Version Update V1.0 Creation, Preliminary 1 3.2 Register ...