AT32UC3A0128 Atmel Corporation, AT32UC3A0128 Datasheet - Page 446

no-image

AT32UC3A0128

Manufacturer Part Number
AT32UC3A0128
Description
Manufacturer
Atmel Corporation

Specifications of AT32UC3A0128

Flash (kbytes)
128 Kbytes
Pin Count
144
Max. Operating Frequency
66 MHz
Cpu
32-bit AVR
# Of Touch Channels
32
Hardware Qtouch Acquisition
No
Max I/o Pins
109
Ext Interrupts
109
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device + OTG
Spi
6
Twi (i2c)
1
Uart
4
Ssc
1
Ethernet
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Dac Channels
2
Dac Resolution (bits)
16
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
YES
External Bus Interface
1
Dram Memory
sdram
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
3.0-3.6 or (1.65-1.95+3.0-3.6)
Operating Voltage (vcc)
3.0-3.6 or (1.65-1.95+3.0-3.6)
Fpu
No
Mpu / Mmu
Yes / No
Timers
10
Output Compare Channels
16
Input Capture Channels
6
Pwm Channels
13
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
AT32UC3A0128-ALUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT32UC3A0128-ALUT
Manufacturer:
Atmel
Quantity:
166
Part Number:
AT32UC3A0128-ALUT
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT32UC3A0128-CTUR
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT32UC3A0128-CTUT
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT32UC3A0128-U
Manufacturer:
ATMEL
Quantity:
2
Part Number:
AT32UC3A0128-U
Manufacturer:
ATMEL/爱特梅尔
Quantity:
20 000
Part Number:
AT32UC3A0128AU-ALUT
Manufacturer:
Atmel
Quantity:
10 000
Part Number:
AT32UC3A0128AU-U
Manufacturer:
ATMEL
Quantity:
4
32058K AVR32-01/12
29.5.4
29.5.5
Receive Block
Address Checking Block
After transmission, no interrupts are generated and the only statistics register that is incre-
mented is the pause frames transmitted register.
The receive block checks for valid preamble, FCS, alignment and length, presents received
frames to the DMA block and stores the frames destination address for use by the address
checking block. If, during frame reception, the frame is found to be too long or rx_er is asserted,
a bad frame indication is sent to the DMA block. The DMA block then ceases sending data to
memory. At the end of frame reception, the receive block indicates to the DMA block whether the
frame is good or bad. The DMA block recovers the current receive buffer if the frame was bad.
The receive block signals the register block to increment the alignment error, the CRC (FCS)
error, the short frame, long frame, jabber error, the receive symbol error statistics and the length
field mismatch statistics.
The enable bit for jumbo frames in the network configuration register allows the MACB to receive
jumbo frames of up to 10240 bytes in size. This operation does not form part of the IEEE802.3
specification and is disabled by default. When jumbo frames are enabled, frames received with a
frame size greater than 10240 bytes are discarded.
The address checking (or filter) block indicates to the DMA block which receive frames should
be copied to memory. Whether a frame is copied depends on what is enabled in the network
configuration register, the state of the external match pin, the contents of the specific address
and hash registers and the frame’s destination address. In this implementation of the MACB, the
frame’s source address is not checked. Provided that bit 18 of the Network Configuration regis-
ter is not set, a frame is not copied to memory if the MACB is transmitting in half duplex mode at
the time a destination address is received. If bit 18 of the Network Configuration register is set,
frames can be received while transmitting in half-duplex mode.
Ethernet frames are transmitted a byte at a time, least significant bit first. The first six bytes (48
bits) of an Ethernet frame make up the destination address. The first bit of the destination
address, the LSB of the first byte of the frame, is the group/individual bit: this is One for multicast
addresses and Zero for unicast. The All Ones address is the broadcast address, and a special
case of multicast.
The MACB supports recognition of four specific addresses. Each specific address requires two
registers, specific address register bottom and specific address register top. Specific address
register bottom stores the first four bytes of the destination address and specific address register
top contains the last two bytes. The addresses stored can be specific, group, local or universal.
The destination address of received frames is compared against the data stored in the specific
address registers once they have been activated. The addresses are deactivated at reset or
when their corresponding specific address register bottom is written. They are activated when
specific address register top is written. If a receive frame address matches an active address,
the frame is copied to memory.
AT32UC3A
446

Related parts for AT32UC3A0128