ATmega1284P Atmel Corporation, ATmega1284P Datasheet - Page 56

• Manufacturer Part Number: ATmega1284P
• Manufacturer: Atmel Corporation

Specifications of ATmega1284P

• Flash (kbytes): 128 Kbytes
• Pin Count: 44
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 32
• Ext Interrupts: 32
• Usb Speed: No
• Usb Interface: No
• Spi: 3
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 16
• Eeprom (bytes): 4096
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

8272C–AVR–06/11
1. In the same operation, write a logic one to the Watchdog change enable bit (WDCE) and
2. Within the next four clock cycles, write the WDE and Watchdog prescaler bits (WDP) as
The following code example shows one assembly and one C function for turning off the Watch-
dog Timer. The example assumes that interrupts are controlled (e.g. by disabling interrupts
globally) so that no interrupts will occur during the execution of these functions.
Note:
Assembly Code Example
C Code Example
WDE. A logic one must be written to WDE regardless of the previous value of the WDE
bit.
desired, but with the WDCE bit cleared. This must be done in one operation.
WDT_off:
void WDT_off(void)
{
}
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Clear WDRF in MCUSR
in
andi
out
; Write logical one to WDCE and WDE
; Keep old prescaler setting to prevent unintentional time-out
in
ori
out
; Turn off WDT
ldi
out
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Clear WDRF in MCUSR */
MCUSR &= ~(1<<WDRF);
/* Write logical one to WDCE and WDE */
/* Keep old prescaler setting to prevent unintentional time-out */
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Turn off WDT */
WDTCSR = 0x00;
__enable_interrupt();
1. The example code assumes that the part specific header file is included.
ATmega164A/PA/324A/PA/644A/PA/1284/P
r16, MCUSR
r16, ~(1<<WDRF)
MCUSR, r16
r16, WDTCSR
r16, (1<<WDCE) | (1<<WDE)
WDTCSR, r16
r16, (0<<WDE)
WDTCSR, r16
(1)
(1)
56