ATmega329A Atmel Corporation, ATmega329A Datasheet - Page 297

• Manufacturer Part Number: ATmega329A
• Manufacturer: Atmel Corporation

Specifications of ATmega329A

• Flash (kbytes): 32 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 54
• Ext Interrupts: 17
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Segment Lcd: 100
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 2
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 4
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

27.5
8284D–AVR–6/11
Boot Loader Lock Bits
ATmega169A/PA/329A/PA/3290A/PA/649A/P/6490A/P
Figure 27-2. Memory Sections
Note:
If no Boot Loader capability is needed, the entire Flash is available for application code. The
Boot Loader has two separate sets of Boot Lock bits which can be set independently. This gives
the user a unique flexibility to select different levels of protection.
The user can select:
• To protect the entire Flash from a software update by the MCU.
• To protect only the Boot Loader Flash section from a software update by the MCU.
• To protect only the Application Flash section from a software update by the MCU.
• Allow software update in the entire Flash.
See
Lock bits can be set in software and in Serial or Parallel Programming mode, but they can be
cleared by a Chip Erase command only. The general Write Lock (Lock Bit mode 2) does not con-
trol the programming of the Flash memory by SPM instruction. Similarly, the general Read/Write
Lock (Lock Bit mode 1) does not control reading nor writing by LPM/SPM, if it is attempted.
Table 27-2
1. The parameters in the figure above are given in
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Program Memory
Program Memory
BOOTSZ = '11'
and
BOOTSZ = '01'
Table 27-3 on page 298
0x0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
0x0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
for further details. The Boot Lock bits and general
Boot Loader Flash Section
Boot Loader Flash Section
Application Flash Section
Application Flash Section
Application Flash Section
Table 27-9 on page
Program Memory
Program Memory
BOOTSZ = '10'
BOOTSZ = '00'
306.
0x0000
End RWW
Start NRWW
End Application
Start Boot Loader
Flashend
0x0000
End RWW, End Application
Start NRWW, Start Boot Loader
Flashend
297