ATtiny261 Atmel Corporation, ATtiny261 Datasheet - Page 171

• Manufacturer Part Number: ATtiny261
• Manufacturer: Atmel Corporation

Specifications of ATtiny261

• Flash (kbytes): 2 Kbytes
• Pin Count: 20
• Max. Operating Frequency: 20 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 4
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 16
• Ext Interrupts: 16
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: Yes
• Crypto Engine: No
• Sram (kbytes): 0.12
• Eeprom (bytes): 128
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.8 to 5.5
• Operating Voltage (vcc): 1.8 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

18.2
2588E–AVR–08/10
Fuse Bytes
The ATtiny261/461/861 have three fuse bytes.
briefly the functionality of all the fuses and how they are mapped into the fuse bytes. Note that
the fuses are read as logical zero, “0”, if they are programmed.
Table 18-3.
Notes:
Table 18-4.
Notes:
SELFPRGEN
Fuse High Byte
RSTDISBL
DWEN
SPIEN
WDTON
EESAVE
BODLEVEL2
BODLEVEL1
BODLEVEL0
Fuse High Byte
(3))
1. Enables SPM instruction. See
(2)
1. See
2. DWEN must be unprogrammed when Lock Bit security is required.
3. The SPIEN Fuse is not accessible in SPI programming mode.
4. Programming this fues will disable the Watchdog Timer Interrupt. See
5. See
(4)
Fuses. After programming the RSTDISBL fuse, parallel programming must be used to change
fuses and allow further programming.
Memory Lock Bits” on page 170.
Timer Control Register” on page 47
(1)
(5)
(5)
(5)
(1)
Fuse Extended Byte
Fuse High Byte
“Alternate Functions of Port B” on page 66
Table 19-6 on page 191
Bit No
Bit No
7
6
5
4
3
2
1
0
7
6
6
4
3
2
1
0
Description
-
-
-
-
-
-
-
Self-Programming Enable
Description
External Reset disable
DebugWIRE Enable
Enable Serial Program and Data
Downloading
Watchdog Timer always on
EEPROM memory is preserved
through the Chip Erase
Brown-out Detector trigger level
Brown-out Detector trigger level
Brown-out Detector trigger level
for BODLEVEL Fuse decoding.
“Self-Programming the Flash” on page
for details.
Table
18-3,
for description of RSTDISBL and DWEN
Table 18-4
Default Value
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
Default Value
1 (unprogrammed)
1 (unprogrammed)
0 (programmed, SPI prog.
enabled)
1 (unprogrammed)
1 (unprogrammed, EEPROM
not preserved)
1 (unprogrammed)
1 (unprogrammed)
1 (unprogrammed)
and
See “Program And Data
165.
“WDTCR – Watchdog
Table 18-5
describe
171