1368062-2 TE Connectivity, 1368062-2 Datasheet - Page 2

• Manufacturer Part Number: 1368062-2
• Manufacturer: TE Connectivity

Specifications of 1368062-2

• Product Type: Connector
• Jack Type: RJ45
• Pcb Mounting Orientation: Side Entry (Right Angle)
• Pcb Mount Style: Through Hole
• Termination Method To Pc Board: Through Hole - Press Fit
• Performance Category: Cat 5
• Number Of Contacts Loaded: 8
• Grounding Options: Panel Ground and PCB Ground
• Panel Stops: Without
• Keyed: No
• Profile: Very Low; Offset - Over Hangs PCB
• Color: Black
• Number Of Terminals Per Port: 8
• Shield Material: .010 [0.25] Copper Alloy
• Jack Configuration: 2 x 4
• Panel Mount Retention: Without
• Shielded: Yes
• Solder Tail Contact Plating: Tin-Lead over Nickel
• Grounding Clips: With
• Port Configuration: Stacked
• Number Of Positions: 8
• Inverted Jack Face: No
• Led: With
• Shield Plating: Bright Tin over Nickel
• Number Of Pcb Ground Tabs: 7
• Pcb Tail Length (mm [in]): 4.35 [0.171]
• Grounding Tab Plating: Tin-Lead over Copper
• Preloaded: Yes
• Contact Plating, Mating Area, Material: Gold (50)
• Contact Base Material: Phosphor Bronze
• Pcb Action Pin Grounds: Without
• Housing Material: PBT - GF
• Housing Color: Black
• Ul Flammability Rating: UL 94V-0
• Rohs/elv Compliance: RoHS compliant, ELV compliant
• Lead Free Solder Processes: Not relevant for lead free process
• Rohs/elv Compliance History: Always was RoHS compliant
• Led Color; Top Left: Green
• Led Color; Top Right: Green
• Led Color; Bottom Left: Green
• Led Color; Bottom Right: Green
• Pcb Thickness, Recommended (mm [in]): 1.57 [0.062]

3.3.
3.4.
3.5.
3.6.
Rev C
Examination of product.
Crosstalk (NEXT).
Ratings
!
!
!
!
Performance and Test Description
Product is designed to meet the electrical, mechanical and environmental performance requirements
specified in Figure 1. Unless otherwise specified, all tests shall be performed at ambient environmental
conditions per Test Specification 109-1.
Test Requirements and Procedures Summary
Product Qualification and Requalification Test Sequence
NOTE
Test Description
Voltage: 150 volts AC
Current: Signal application only, 1.5 amperes AC rms maximum at 25° C derated to .2 ampere AC
rms maximum at 70° C ambient
Temperature:
•
•
Shielding effectiveness: -20 dB minimum reduction from 30 to 400 MHz
Jacks: -40 to 85° C
Plugs: -40 to 60° C
(a)
(b)
Examination of product
Crosstalk (NEXT)
See paragraph 4.1.A.
Numbers indicate sequence in which tests are performed.
Test or Examination
Meets requirements of product
drawing and Application
Specifications 114-2048 and 114-
6053.
Frequency (MHz)
31.25
100.0
10.0
16.0
20.0
25.0
62.5
1.0
4.0
8.0
Requirement
Figure 1
Figure 2
NEXT (dB)
65.0
65.0
62.0
60.0
56.0
54.0
52.0
50.0
44.0
40.0
Test Sequence (b)
Test Group (a)
1,3
Visual, dimensional and functional
per applicable quality inspection
plan.
TE Spec 109-194.
Test NEXT - TOC of each sample
on each of 5 test plugs qualified
per paragraph 3.2. of TE Spec 109-
194. All pair combinations to be
tested for NEXT - TOC Y driven
pair-quiet pair: 45-36, 45-12, 45-78,
36-78, 36-12, and 12-78.
See Figure 3.
1
2
Procedure
108-1163-2
2 of 4