184344-1 TE Connectivity, 184344-1 Datasheet - Page 4

• Manufacturer Part Number: 184344-1
• Manufacturer: TE Connectivity

Specifications of 184344-1

• Product Line: Sealed Sensor Connector (SSC)
• Product Type: Connector
• Connector Type: Housing
• Wire/cable Type: Discrete Wire
• Termination Method To Wire/cable: Crimp
• Accessory Color: Red, Yellow
• Strain Relief: Without
• Sealed: Yes
• Mating Retention Type: Latching
• Keying: A
• Panel Mount Retention: Without
• Contact - Rated Current (a): 10 – 17
• Operating Voltage Reference: AC/DC
• Operating Voltage (vac): 125
• Operating Voltage (vdc): 125
• Wire/cable Size (awg): 14 – 20, 18 – 22
• Wire/cable Size (mm²): 0.3 – 1, 0.5 – 2
• Seal Type: Seal Ring
• Profile Height (y-axis) (mm [in]): 30.60 [1.2047]
• Wire Type: Stranded
• Number Of Positions: 4
• Number Of Rows: 2 x 2
• Mating Retention: With
• Seal Material: Silicone Rubber
• Seal Color: Brown
• Length (x-axis) (mm [in]): 27.60 [1.086]
• Width (z-axis) (mm [in]): 23.20 [0.9133]
• Contact Type: Socket
• Circuit Number(s) Blocked: None
• Connector Style: Plug
• Housing Material: PBT - GF15
• Housing Color: Black
• Mating Alignment: With
• Mating Alignment Type: Keyed
• Rohs/elv Compliance: ELV compliant
• Lead Free Solder Processes: Not reviewed for lead free solder process
• Rohs/elv Compliance History: Always was ELV compliant
• Ip Dust Sealing Level: 6
• Ip Water Sealing Level: 7, 4
• Agency/standard: SAE/USCAR-2, IEC 529 IP 65/67
• Operating Temperature (°c [°f]): -40 – +125 [-40 – +257]
• Applies To: Wire/Cable
• Accepts Wire Insulation Diameter, Range (mm [in]): 1.20 – 2.10 [0.047 – 0.082], 1.20 – 2.70 [0.047 – 0.106]
• Application Use: Wire-to-Wire / Wire-to-Device
• Contact Transmits (typical Application): Power
• Packaging Method: Carton
• Packaging Quantity: 1000

Rev B
High temperature exposure.
Humidity-temperature cycling.
Immersion.
Pressure/vacuum leak.
NOTE
Test Description
Shall meet visual requirements, show no physical damage, and meet requirements of additional
tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure
2.
See Note.
See Note.
No evidence of leakage.
See Note.
No evidence of leakage.
See Note.
Figure 1 (end)
Requirement
USCAR 5.6.3. (Rev 4/01)
Subject mated specimens to
temperature life at 125° C for PBT
housings and 150° C for nylon
housings for 1008 hours.
USCAR 5.6.2. (Rev 4/01)
Subject mated specimens to 15
specified cycles.
See Figure 8.
USCAR 5.3.15. (Rev 8/97)
Subject mated specimens to the
following procedure:
1. Temperature soak specimens for
2 hours at 125° C for PBT housings
and 150° C for nylon housings.
2. Remove specimens from oven
and immediately immerse in 25° C
5% salt solution for 2 hours.
Measure dry circuit resistance.
3. Repeat procedure 4 more times.
USCAR 5.3.16. (Rev 8/97)
Subject mated specimens to the
following procedure:
1. Immerse specimens in 25° C 5%
salt solution and slowly pressurize
to 48 kpa while observing for air
bubbles.
2. Remove pressure and slowly
apply 48 kpa of vacuum.
3. Unmate specimens and examine
for leakage.
4. Temperature soak specimens for
72 hours at 125° C for PBT
housings and 150° C for nylon
housings.
5. Remove specimens and repeat
steps 1 and 2 using 28 kpa.
Procedure
108-1790
4 of 9