MAX901BCSE+ Maxim Integrated Products, MAX901BCSE+ Datasheet - Page 6

• Manufacturer Part Number: MAX901BCSE+
• Description: IC COMPARATOR QUAD HS LP 16-SOIC
• Manufacturer: Maxim Integrated Products
• Type: General Purposer

Specifications of MAX901BCSE+

• Number Of Elements: 4
• Output Type: TTL
• Voltage - Supply: 5 V ~ 10 V, ±2.5 V ~ 5 V
• Mounting Type: Surface Mount
• Package / Case: 16-SOIC (0.154", 3.90mm Width)
• Number Of Channels: 4 Channels
• Supply Voltage (max): 10 V
• Supply Voltage (min): 5 V
• Supply Current (max): 15 mA
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Propagation Delay Time: 8 ns
• Comparator Type: High Speed
• No. Of Comparators: 4
• Response Time: 8ns
• Ic Output Type: TTL
• Supply Current: 10mA
• Supply Voltage Range: 5V To 10V, ± 4.75V To ± 5.25V
• Amplifier Case Style: SOIC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ELECTRICAL CHARACTERISTICS (continued)
(V
TIMING CHARACTERISTICS
(V
Note 1: The input common-mode voltage and input signal voltages should not be allowed to go negative by more than 0.2V below
Note 2: Tested for +4.75V < V
Note 3: Specification does not apply to MAX901.
Note 4: Guaranteed by design. Times are for 100mV step inputs (see Propagation Delay Characteristics in Figures 2 and 3).
Note 5: Maximum difference in propagation delay between any of the four comparators in the MAX900–MAX903.
Note 6: See Timing Diagram (Figure 2). Owing to the difficult and critical nature of switching measurements involving the latch,
Note 7: I
Positive Analog
Supply Current
Negative Analog
Supply Current
Digital Supply
Current
Power
Dissipation
Input-to-Output High
Response Time
Input-to-Output Low
Response Time
Difference in Response
Time Between Outputs
CC
CC
PARAMETER
= +5V, V
= +5V, V
High-Speed, Low-Power Voltage Comparators
PARAMETER
V
of V
range is +4.75V < V
these parameters cannot be tested in a production environment. Typical specifications listed are taken from measurements
using a high-speed test-jig.
for +4.75V < V
CC
EE
. The upper-end of the common-mode voltage range is typically V
CC
tested for +4.75V < V
EE
EE
+ 0.2V without damage.
= -5V, V
= -5V, V
SYMBOL
_______________________________________________________________________________________
DD
I
I
I
P
CC
DD
EE
D
DD
DD
< +5.25V with the worst-case condition of all four comparator outputs at logic low.
CC
= +5V, LE1–LE4 = logic high, T
= +5V, LE1–LE4 = logic high, T
SYMBOL
CC
< +10.5V for single-supply operation with V
∆t
t
t
(Note 7)
(Note 7)
(Note 7)
V
+5V, V
pd+
pd-
CONDITIONS
< +5.25V, and -5.25V < V
pd
CC
CC
= V
< +10.5V with V
EE
DD
= 0
CONDITIONS
V
C
I
(Note 4)
V
C
I
(Note 4)
(Notes 4, 5)
=
O
O
OD
OD
L
L
= 2mA
= 2mA
= 15pF,
= 15pF,
= 5mV,
= 5mV,
MAX900A/MAX901A/
MAX900B/MAX901B
MIN
EE
grounded. I
TYP
EE
10
70
A
7
4
A
MIN
= full operating temperature, unless otherwise noted.)
= full operating temperature, unless otherwise noted.)
< -4.75V with V
MAX900A/MAX901A
MAX
105
25
20
10
EE
tested for -5.25V < V
TYP
10
10
1
EE
MIN
DD
CC
grounded.
= +5V, although permissible analog power-supply
- 2V, but either or both inputs can go to a maximum
MAX
MAX902
15
15
3
TYP
3.5
35
5
2
EE
MIN
MAX
12
10
55
MAX900B/MAX901B/
5
< -4.75V with V
MAX902/MAX903
MIN
TYP
10
10
1
MAX903
TYP
CC
2.5
18
2
1
MAX
= +5V. I
15
15
3
MAX
2.5
28
6
5
DD
UNITS
tested
ns
ns
ns
UNITS
mW
mA
mA
mA
5