2-353082-3 TE Connectivity, 2-353082-3 Datasheet
2-353082-3
Specifications of 2-353082-3
Related parts for 2-353082-3
2-353082-3 Summary of contents
Page 1
... Tyco Electronics Japan G.K. (3-5-8 Hisamoto Takatsu-ku Kawasaki, 213-8535) © Copyright 2009 Tyco Electronics Japan G.K. All international rights reserved 商標 Trademark Product Specification 製 ...
Page 2
... Finish: Tin plating 3.3 Ratings : A. Voltage Rating : 630V AC/DC B. Current Rating: Refer to Fig.4 for maximum allowable current to be applied. Temperature Rating : －55℃ to 105℃ C. 108-5453 Gold plating(contact area) or Silver plating (all over) Gold plating(contact area) and Tin plating(tine area) or Silver plating(all over) ...
Page 3
... Silver plating products, 1-3pos. conducting. 電線 #20 #18 Wire 電流 Current 銀めっき製品 4 極通電の場合 / Silver plating products, 4pos. conducting. 単位:A / Unit: A 電線 #20 #18 Wire 電流 Current Fig.1 定 ...
Page 4
... MIL-STD-202 試験法 302 条件 B Impressed voltage 500 V DC. Test between adjacent circuits of mated/ unmated connectors. MIL-STD-202 Method 302 condition B 通電による温度上昇を測定すること。 Fig.5 参照 EIA364-70 コ ...
Page 5
... No electrical discontinuity greater than 1µsec. Shall Physical Shock occur. Meet requirement of Contact resistance (2 m Max.) Rev. C Product Specification 規格値 Requirements 機械的性能 Mechanical Requirements 電線ｻｲｽﾞ ...
Page 6
... Mating Force 1.96N -19.6N（初期値、1 極当たり） 3.5.10 コネクタ 引抜力 3.5.10 1.96N – 19.6N per 1 contact (Initial) Connector Unmating Force コンタクト 9.8N 以下（1 極当たり） 3.5.11 装 ...
Page 7
... MIL-STD-202 試験法 107 条件 A-1 Mated connector －55℃ / 30min., 85℃ / 30min. Making this a cycle, repeat 25 cycles. MIL-STD-202 Method 107,condition A-1 嵌合した／しないコネクタ 25～65℃、 90～95％ R.H. 10 サイクル ...
Page 8
... MIL-STD-202 試験法 108 Mated connector 105 ℃, Duration: 250hours MIL-STD-202 Method 108 嵌合したコネクタ ℃、504 時間 ...
Page 9
... Fig. 3 製品認定試験の試験順序 / Product Qualification Test Sequence Test Fig.4 総 ...
Page 10
... L はんだ付け Soldered Fig.5 温度上昇測定 / Measurement of Temperature rising Rev. C Product Specification L 2L 電線/WIRE Ｌ AWG#8 57cm AWG#10 50cm AWG#12 42cm AWG#14 36cm AWG#16 29cm AWG#18 25cm AWG#20 20cm 温度測定位置 ...
Page 11
... Acceptance: Acceptance is based on verification that the product meets the requirements of Figure.2 Failures attributed to equipment,test get up, or operator deficiencies shall not disqualify the product. When product failure occurs,corrective action shall be taken and samples resubmitted for qualification ...