849813-5 TE Connectivity, 849813-5 Datasheet

849813-5

Manufacturer Part Number

849813-5

Description

Manufacturer

TE Connectivity

Datasheets

1.849813-5.pdf (1 pages)

2.849813-5.pdf (6 pages)

Specifications of 849813-5

Product Type

Lead Assembly

Mount Angle

Straight

Cap Material

Glass-Filled Polyester

Wire Size (mm² [awg])

Operating Voltage (kvdc)

Shielded

Lead Assembly Type

Double-End

Assembly Length (mm [in])

609.60 [24.000]

Barrel Depth (mm [in])

13.50 [0.530]

Positive Stop Ferrule

Without

Wire Color

White (Standard)

Cap Color

Green

Wire Insulation

Silicone

Preloaded

Yes

Rohs/elv Compliance

Not reviewed for ELV/RoHS compliance

Lead Free Solder Processes

Not reviewed for lead free solder process

Current page: 1 of 6
Download datasheet (271Kb)

DESIGN OBJECTIVES

The product described in this document has not been fully tested to ensure conformance to the requirements outlined below. Therefore

Tyco Electronics makes no representation or warranty, express or implied, that the product will comply with these requirements. Further,

Tyco Electronics may change these requirements based on the results of additional testing and evaluation. Contact Tyco Electronics

Engineering for further details.

1.1.

1.2.

2.1.

2.2.

2.3.

3.1.

a TE Connectivity Ltd. Company

TE logo is a trademark.

SCOPE

Content

This specification covers perform ance, tests and quality requirem ents for the Tyco Electronics LGH

standard high voltage 1/2I, 1/2LI, 1I, 1LI, 2I, 3I and 4I series m olded end leads and receptacles. These

leads and receptacles are designed for com m ercial, industrial and m ilitary type applications requiring

operation over wide environm ents.

Qualification

W hen tests are perform ed on the subject product line, procedures specified in Figure 1 shall be used.

All inspections shall be perform ed using the applicable inspection plan and product drawing.

APPLICABLE DOCUM ENTS

The following docum ents form a part of this specification to the extent specified herein. Unless

otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the

requirem ents of this specification and the product drawing, the product drawing shall take precedence.

In the event of conflict between the requirem ents of this specification and the referenced docum ents,

this specification shall take precedence.

Tyco Electronics Docum ents

Com m ercial Standard

EIA-364:

Military Standard

MIL-STD-202: Test Methods For Electronic And Electrical Com ponent Parts

REQUIREM ENTS

Design and Construction

Product shall be of the design, construction and physical dim ensions specified on the applicable product

drawing.

109 Series: Test Specifications as indicated in Figure 1

109-197: Test Specification (AMP Test Specifications vs EIA and IEC Test Methods)

114-

501-

: Application Specification

: Qualification Test Report

PRELIMINARY

Electrical Connector/Socket Test Procedures Including Environm ental Classifications

| Indicates change

*Trademark

Design

Objectives

Standard LGH Connectors,

Series 1/2I, 1/2LI, 1I, 1LI, 2I, 3I and 4I

For latest revision, visit our website at www.te.com/documents.

For Regional Customer Service, visit our website at www.te.com

Other products, logos, and company names might be trademarks of their respective owners.

108-36033

Rev O2

1 of 6

LOC B

Related parts for 849813-5

849813-5 Summary of contents

Page 1

... PRELIMINARY Product shall be of the design, construction and physical dim ensions specified on the applicable product drawing. ©2011 Tyco Electronics Corporation, | Indicates change a TE Connectivity Ltd. Company *Trademark All Rights Reserved TE logo is a trademark. For latest revision, visit our website at www.te.com/documents. ...

Page 2

Materials Materials used in the construction of this product shall be as specified on the applicable product drawing. 3.3. Ratings ! Voltage: • 1/2I: 10 kilovolts • 1/2LI: 15 kilovolts • 1I: 20 kilovolts • 1LI: 25 kilovolts • ...

Page 3

Test Description Vibration, sinusoidal. Mechanical shock. Durability. Contact engaging force. Contact separating force. Therm al shock. Hum idity, steady state. Tem perature life. Rev O2 Requirem ent MECHANICAL No discontinuities icroseconds or longer duration. See Note. No ...

Page 4

Test Description Barom etric pressure, tem perature cycling. Herm etic seal. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification and Requalification Test Sequence shown in Figure 2. ...

Page 5

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specim en Selection Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Test group 1 shall consist of 28 lead assem ...

Page 6

Gage Num ber 1 2 (a) Contact: Size 16 NOTE (b) Material: Tungsten carbide Rev O2 Figure 3 Contact Resistance Measurem ent Points A Dim ension .0165 +.0001/-.0000 .0635 +.0000/-.0001 Figure 4 Engaging & Separating Gage 108-36033 B Dim ension ...

Related keywords

849813-5 datasheet
849813-5 data sheet
849813-5 pdf datasheet
849813-5 component
849813-5 part
849813-5 distributor
849813-5 RoHS
849813-5 datasheet download