505038-1 TE Connectivity, 505038-1 Datasheet

505038-1

Manufacturer Part Number
505038-1
Description
Manufacturer
TE Connectivity
Datasheets

Specifications of 505038-1

Product Type
Contact
Pin Size (mm [in])
4.57 [0.180]
Insulation Support
Insulation Support
Wire/cable Type
Regular Wire
Insulation Diameter (mm [in])
2.29-3.18 [.090-.125]
Finish
None
Product Line
SHUR-PLUG
Wire Range (mm [awg])
0.50-1.40² [20-16]
Stock Thickness (mm [in])
0.46 [0.018]
Rohs/elv Compliance
RoHS compliant, ELV compliant
Lead Free Solder Processes
Not relevant for lead free process
Rohs/elv Compliance History
Always was RoHS compliant
1.
1.1.
1.2.
1.3.
2.
2.1.
2.2.
3.
3.1.
3.2.
©2008 Tyco Electronics Corporation
Harrisburg, PA
All International Rights Reserved.
SCOPE
Content
This specification covers perform ance, tests and quality requirem ents for SHUR-PLUG* and
SHUR-PLUG* receptacles. The .180 inch diam eter SHUR-PLUG is only available as a straight contact
while SHUR-PLUG receptacles are available in straight and right angle versions.
Qualification
W hen tests are perform ed on the subject product line, procedures specified in Figure 1 shall be used.
All inspections shall be perform ed using the applicable inspection plan and product drawing.
Successful qualification testing on the subject product line was com pleted on 28May08. The
Qualification Test Report num ber for this testing is 501-688. This docum entation is on file at and
available from Engineering Practices and Standards (EPS).
APPLICABLE DOCUM ENTS
The following docum ents form a part of this specification to the extent specified herein. Unless
otherwise specified, the latest edition of the docum ent applies. In the event of conflict between the
requirem ents of this specification and the product drawing, the product drawing shall take precedence.
In the event of conflict between the requirem ents of this specification and the referenced docum ents,
this specification shall take precedence.
Tyco Electronics Docum ents
!
!
!
Industry Docum ent
EIA-364: Electrical Connector/Socket Test Procedures Including Environm ental Classifications
REQUIREM ENTS
Design and Construction
Product shall be of the design, construction and physical dim ensions specified on the applicable product
drawing.
Materials
Materials used in the construction of this product shall be as specified on the applicable product
drawing.
109-197: Test Specification (Tyco Electronics Test Specifications vs EIA and IEC Test Methods)
114-2042: Application Specification (SHUR-PLUG* .156 Diam eter Term inals and Receptacle
Contacts)
501-688: Qualification Test Report ( SHUR-PLUG* and SHUR-PLUG* Receptacles)
* Trademark
| Indicates change
Product
Specification
SHUR-PLUG* and SHUR-PLUG* Receptacles
For latest revision, visit our website at www.tycoelectronics.com\documents.
For Regional Customer Service, visit our website at www.tycoelectronics.com
108-1889
08Sep08 Rev A
1 of 6
LOC B

Related parts for 505038-1

505038-1 Summary of contents

Page 1

SCOPE 1.1. Content This specification covers perform ance, tests and quality requirem ents for SHUR-PLUG* and SHUR-PLUG* receptacles. The .180 inch diam eter SHUR-PLUG is only available as a straight contact while SHUR-PLUG receptacles are available in straight and ...

Page 2

Ratings ! Voltage: 110 volts DC ! Current: See Figure 3 for applicable current carrying capability ! Tem perature: -40 to 105 C 3.4. Perform ance and Test Description Product is designed to m eet the electrical, m echanical ...

Page 3

Test Description Sinusoidal vibration. Mechanical shock. Durability. Mating force. Unm ating force. Hum idity/tem perature cycling. Tem perature life. Shall meet visual requirements, show no physical damage, and meet requirements of additional NOTE tests as specified in the Product Qualification ...

Page 4

Product Qualification and Requalification Test Sequence Initial exam ination of product LLCR Contact resistance, specified current Tem perature rise vs current Crim p tensile Sinusoidal vibration Mechanical shock Durability Mating force Unm ating force Hum idity/tem perature cycling Tem ...

Page 5

QUALITY ASSURANCE PROVISIONS 4.1. Qualification Testing A. Specim en Selection Specim ens shall be prepared in accordance with applicable Instruction Sheets and shall be selected at random from current production. Each test group shall consist inim ...

Page 6

Percent Connector Loading Single Contact To determine acceptable current carrying capacity for percentage connector loading and wire gage NOTE indicated, use the Multiplication Factor (F) from the above chart and multiply it times the Base rated Current for a single ...

Related keywords