MAX4018 Maxim, MAX4018 Datasheet
MAX4018
Available stocks
Related parts for MAX4018
MAX4018 Summary of contents
Page 1
... The MAX4012 single, MAX4016 dual, MAX4018 triple, and MAX4020 quad op amps are unity-gain-stable devices that combine high-speed performance with Rail- to-Rail outputs. The MAX4018 has a disable feature that reduces power-supply current to 400µA and places its outputs into a high-impedance state. These devices operate from a 3.3V to 10V single supply or from ± ...
Page 2
... Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300° / / OUT CC A MIN MAX CONDITIONS Guaranteed by CMRR test Any channels for MAX4016/MAX4018/ MAX4020 (Note 2) (Note 2) Differential mode (-1V V +1V) IN Common mode (-0.2V V +2.75V 0.2V 2.25V) ...
Page 3
... EN_ = (Note 4) OUT 0.2V) EN_ EN_ = 0 I EN_ = 5V IH Enabled I S MAX4018, disabled (EN_ = 0) , unless otherwise noted. Typical values are at T MAX MIN TYP MAX 3. 1.6 CC 0.5 200 400 0.5 10 5.5 7.0 0.40 0.65 ...
Page 4
... OUT P-P Total harmonic distortion f1 = 10.0MHz 10.1MHz, V OUT f = 10MHz VCL NTSC 150 L NTSC 150 10kHz f = 10kHz MAX4018, EN_ = 10MHz MAX4018 MAX4018 MAX4016/MAX4018/MAX4020 10MHz 20mV OUT P-P MAX4016/MAX4018/MAX4020 10MHz ground OUT P +25°C. Specifications over temperature limits are guaranteed 4.5V to 5.5V ...
Page 5
... FREQUENCY (Hz) LARGE-SIGNAL GAIN vs. FREQUENCY OUT P 1.75V OUT BIAS 100k 1M 10M 100M 1G FREQUENCY (Hz) MAX4016/MAX4018/MAX4020 CROSSTALK vs. FREQUENCY -10 -30 -50 -70 -90 -110 -130 -150 1G 100k 1M 10M 100M FREQUENCY (Hz) MAX4012 SMALL-SIGNAL GAIN vs. FREQUENCY ( VCL 9 ...
Page 6
Low-Cost, High-Speed, Single-Supply Op Amps with Rail-to-Rail Outputs ( VCL F HARMONIC DISTORTION vs. FREQUENCY ( VCL OUT P-P ...
Page 7
Low-Cost, High-Speed, Single-Supply ( VCL F SMALL-SIGNAL PULSE RESPONSE ( VCL MAX4012-19 IN (50mV/ div) OUT (25mV/ div) 20ns/div V = 2.5V, R ...
Page 8
Low-Cost, High-Speed, Single-Supply Op Amps with Rail-to-Rail Outputs ( VCL F OPEN-LOOP GAIN vs. LOAD RESISTANCE 200 400 ...
Page 9
... MAX4018 MAX4020 NAME SO QSOP SO QSOP — — N.C. — — — — OUT — ...
Page 10
... Applications Information Choosing Resistor Values Unity-Gain Configuration The MAX4012/MAX4016/MAX4018/MAX4020 are inter- nally compensated for unity gain. When configured for unity gain, the devices require a 24 series with the feedback path. This resistor improves ...
Page 11
... This resistor provides a feedback mechanism that increases V input is brought to V input current (I When the MAX4018 is disabled, the amplifier’s output impedance is 35k . This high resistance and the low 2pF output capacitance make this part ideal in RF/video multiplexer or switch applications. For larger arrays, pay careful attention to capacitive loading ...
Page 12
... Output Capacitive Loading and Stability The MAX4012/MAX4016/MAX4018/MAX4020 are opti- mized for AC performance. They are not designed to drive highly reactive loads, which decreases phase margin and may produce excessive ringing and oscilla- tion ...
Page 13
Low-Cost, High-Speed, Single-Supply Op Amps with Rail-to-Rail Outputs MAX40_ TIN Figure 5. Driving a Capacitive Load through an Isolation Resistor 10pF ...
Page 14
... MAX4018 INB+ INA INA INB- OUTB OUTA ENA 1 16 OUTC INC- ENC 2 15 INC+ ENB 3 14 MAX4018 INB+ INA INA INB- OUTA 7 OUTB 10 N.C. 9 N.C. 8 QSOP 14 ______________________________________________________________________________________ Pin Configurations (continued) EE OUTA ...
Page 15
... For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ ___________________Chip Information MAX4012 TRANSISTOR COUNT: 95 PIN- TOP MAX4016 TRANSISTOR COUNT: 190 PACKAGE MARK MAX4018 TRANSISTOR COUNT: 299 14 SO — MAX4020 TRANSISTOR COUNT: 362 16 QSOP — — 16 QSOP — ...
Page 16
... Low-Cost, High-Speed, Single-Supply Op Amps with Rail-to-Rail Outputs (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) 8 ÿ 0.50±0.1 0.6±0.1 1 0.6±0.1 D TOP VIEW A2 e FRONT VIEW 16 ______________________________________________________________________________________ Package Information (continued) ...
Page 17
... A1 FRONT VIEW Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 17 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...