MAX4433 Maxim, MAX4433 Datasheet
MAX4433
Related parts for MAX4433
MAX4433 Summary of contents
Page 1
... The MAX4431/MAX4433 are compen- sated for closed-loop gains greater and have a small-signal -3dB bandwidth of 215MHz. The MAX4430–MAX4433 op amps require only 11mA of supply current per amplifier while achieving 125dB open- loop gain. Voltage noise density is a low 2.8nV/√Hz, and provides 100dB spurious-free dynamic range (SFDR) at 1MHz ...
Page 2
... SO (derate 5.88mW/°C above +70°C)................471mW Note 1: The MAX4430–MAX4433 are not protected for output short-circuit conditions. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied ...
Page 3
... MAX4431/MAX4433 (A = +2) VCL step OUT step OUT step, OUT MAX4430/MAX4432 step, OUT MAX4431/MAX4433 (A = +2) VCL step, OUT MAX4430/MAX4432 step, OUT MAX4431/MAX4433 (A = +2) VCL MIN TYP MAX UNITS 180 ...
Page 4
... 4Vp-p centered at 2V, OUT f = 1MHz (R = 10kΩ 100kHz 100kHz 1MHz OUT MAX4432/MAX4433 f = 1MHz C = +25°C. All temperature limits are guaranteed by design. A MIN TYP MAX UNITS -84 dB -77 dB -110 -105 -105 -103 ...
Page 5
... SMALL-SIGNAL PULSE RESPONSE A VCL INPUT 25mV/div OUTPUT 50mV/div 10ns/div MAX4430/MAX4432 GAIN FLATNESS vs. FREQUENCY (A = +1V/V) VCL 1.0 100mVp-p 0.8 0.6 0.4 0.2 0 -0.2 -0.4 -0.6 -0.8 -1.0 1M 10M 100M 1G FREQUENCY (Hz) MAX4431/MAX4433 LARGE-SIGNAL GAIN vs. FREQUENCY (A = +2V/V) VCL 4 1Vp 10M 100M FREQUENCY (Hz) MAX4430/MAX4432 LARGE-SIGNAL PULSE RESPONSE = +2V/V INPUT 500mV/V OUTPUT 500mV/div 10ns/div ...
Page 6
... OUTPUT 500mV/div 10ns/div OUTPUT ISOLATION RESISTANCE vs. CAPACITIVE LOAD 12 10 MAX4430 8 6 MAX4431 100 125 150 175 200 CAPACITIVE LOAD (pF) MAX4431/MAX4433 SMALL-SIGNAL PULSE RESPONSE A = +1V/V VCL C = 15pF L INPUT 25mV/div OUTPUT 50mV/div 10ns/div POWER-SUPPLY REJECTION RATIO vs. FREQUENCY 0 -10 -20 -30 -40 -50 ...
Page 7
Dual-Supply, 180MHz, 16-Bit Accurate +5V -5V 500Ω MAX4430 GAIN AND PHASE vs. FREQUENCY MAX4430 toc19 120 A = 1000 V 80 GAIN 40 0 -40 PHASE -80 -120 -160 ...
Page 8
... NAME OUTA Amplifier A Output INA- Amplifier A Inverting Input INA+ Amplifier A Noninverting Input V Negative Power Supply EE INB+ Amplifier B Noninverting Input INB- Amplifier B Inverting Input OUTB Amplifier B Output V Positive Power Supply CC MAX4432/MAX4433 CROSSTALK vs. FREQUENCY 1 10 100 1000 FREQUENCY (MHz) Pin Description FUNCTION FUNCTION ...
Page 9
... F S Figure 2a. Noninverting Configuration _______________________________________________________________________________________ Ultra-Low Distortion Op Amps and 2 for the MAX4431/MAX4433. Use care in selecting the value for the resistor marked R From dynamic stability considerations (based on the part’s frequency response and the input capacitance of the MAX4430–MAX4433), the maximum recommended ...
Page 10
... IC pins as possible. Driving Capacitive Loads MAX4430–MAX4433 can drive capacitive loads. However, excessive capacitive loads may cause ring- ing or instability at the output as phase margin is reduced. Adding a small isolation resistor in series with ...
Page 11
Dual-Supply, 180MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps ______________________________________________________________________________________ Package Information 11 ...
Page 12
... Dual-Supply, 180MHz, 16-Bit Accurate, Ultra-Low Distortion Op Amps Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...