MAX9010 Maxim, MAX9010 Datasheet
MAX9010
Available stocks
Related parts for MAX9010
MAX9010 Summary of contents
Page 1
... MAX913 and LT1016/LT1116, offering lower power and higher speed when used in a single 5V supply application. For space-critical designs, the single MAX9010 is avail- able in the tiny 6-pin SC70 package. The single MAX9011 is available in a space-saving 6-pin SOT23 package. The dual MAX9012 and the single MAX9013 are available in 8-pin µ ...
Page 2
... Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (MAX9010/MAX9011 5V, V ...
Page 3
... SC70, 5ns, Low-Power, Single-Supply, ELECTRICAL CHARACTERISTICS (MAX9010/MAX9011) (continued 5V (MAX9011 only PARAMETER SYMBOL Latch Setup Time (Note 8) Latch Hold Time (Note 8) Latch Propagation Delay t (Note 8) Input Noise-Voltage Density Propagation Delay (Note 6) t PD+ Output Rise Time Output Fall Time ...
Page 4
... ON Note 1: All specifications are 100% tested at T Note 2: Quiescent Power-Supply Current is slightly higher with the comparator output at V case condition for the MAX9010/MAX9011 and both outputs at V OUT OL has complementary outputs, the power-supply current is specified with either OUT = V V (power-supply current is equal in either case). ...
Page 5
... the interval after the latch is asserted in which the input signal must remain the delay time for the output to respond when the latch enable pin is deasserted LPD Typical Operating Characteristics RESPONSE TO -5mV OVERDRIVE MAX9010–13 toc02 +100mV OUT 5ns/div ...
Page 6
... CC 6 _______________________________________________________________________________________ Typical Operating Characteristics (continued) PROPAGATION DELAY vs. LOAD CAPACITANCE 8.0 7.5 7.0 t PD(-) 6.5 6.0 t 5.5 PD(+) 5.0 4.5 4.0 10k LOAD CAPACITANCE (pF) RESPONSE TO 10kHz TRIANGLE WAVE MAX9010–13 toc08 20µs/div A: Input, 20mV/div B: Output, 2V/div INPUT BIAS CURRENT vs. TEMPERATURE 0.7 0 -0.2V CM 0.5 0 3.1V CM 0.3 0.2 -40 - TEMPERATURE (° ...
Page 7
... GND Ground 2 IN+ Noninverting Input 3 IN- Inverting Input Positive Power-Supply Voltage. Pins 5 and 6 of the 1 V MAX9010 must BOTH be connected to the power- CC supply rail. Bypass with a 0.1µF capacitor Latch Enable Input — INA+ Noninverting Input, Channel A — INA- Inverting Input, Channel A — ...
Page 8
SC70, 5ns, Low-Power, Single-Supply, Precision TTL Comparators V IN (DIFFERENTIAL) LATCH ENABLE (LE) t PD+ OUT Figure 1. Timing Diagram IN+ IN- OUT WITH HYSTERESIS IDEAL (WITHOUT HYSTERESIS) * WHEN HYSTERESIS IS ADDED, A COMPARATOR CANNOT RESOLVE ANY INPUT SIGNAL ...
Page 9
... PART COMPARATORS LATCH MAX9010 1 No MAX9011 1 Yes MAX9012 2 No MAX9013 1 Yes _______________________________________________________________________________________ Precision TTL Comparators MAX9010 TRANSISTOR COUNT: 106 COMPLEMENTARY MAX9011 TRANSISTOR COUNT: 137 OUTPUTS MAX9012 TRANSISTOR COUNT: 212 No MAX9013 TRANSISTOR COUNT: 145 No No PROCESS: Bipolar Yes Chip Information Package Information 9 ...
Page 10
SC70, 5ns, Low-Power, Single-Supply, Precision TTL Comparators 10 ______________________________________________________________________________________ Package Information (continued) ...
Page 11
SC70, 5ns, Low-Power, Single-Supply, Precision TTL Comparators ______________________________________________________________________________________ Package Information (continued) 11 ...
Page 12
... SC70, 5ns, Low-Power, Single-Supply, Precision TTL Comparators Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...