MAX9118 Maxim, MAX9118 Datasheet
MAX9118
Related parts for MAX9118
MAX9118 Summary of contents
Page 1
... The MAX9117/MAX9119 have a push-pull output stage that sinks and sources current. Large internal-output drivers allow rail-to-rail output swing with loads up to 5mA. The MAX9118/MAX9120 have an open-drain output stage that makes them suit- able for mixed-voltage system design. All devices are available in the ultra-small 5-pin SC70 package ...
Page 2
... Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS—MAX9117/MAX9118 (with REF +5V, V ...
Page 3
... SC70, 1.6V, Nanopower, Beyond-the-Rails Comparators With/Without Reference ELECTRICAL CHARACTERISTICS—MAX9117/MAX9118 (with REF) (continued +5V 0V IN+ REF A PARAMETER SYMBOL Low-to-High Propagation Delay (Note 4) Rise Time Fall Time Power-Up Time Reference Voltage Reference Voltage Temperature Coefficient Reference Output Voltage Noise ...
Page 4
... Note 3: The hysteresis-related trip points are defined as the edges of the hysteresis band, measured with respect to the center of the band (i.e (Figure 2). OS Note 4: Specified with an input overdrive (V above and beyond the offset voltage and hysteresis of the comparator input. For the MAX9117/MAX9118, reference voltage error should also be added. 4 _______________________________________________________________________________________ CONDITIONS T = +25° ...
Page 5
... SC70, 1.6V, Nanopower, Beyond-the-Rails Comparators With/Without Reference (V = +5V 0V 15pF OVERDRIVE MAX9117/MAX9118 SUPPLY CURRENT vs. SUPPLY VOLTAGE AND TEMPERATURE 950 900 T = +85°C A 850 800 750 T = +25°C A 700 650 T = -40°C 600 A 550 500 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 SUPPLY VOLTAGE (V) MAX9119/MAX9120 SUPPLY CURRENT vs. TEMPERATURE ...
Page 6
... V = +5V CC 1.256 1.254 1.252 V = +3V CC 1.250 V = +1.8V CC 1.248 1.246 1.244 1.242 1.240 -40 - TEMPERATURE (°C) MAX9117/MAX9118 REFERENCE OUTPUT VOLTAGE vs. REFERENCE SINK CURRENT 1.260 1.258 1.256 V = +5V CC 1.254 1.252 1.250 V = +1. + 1.248 1.246 1.244 1.242 1.240 ...
Page 7
... TEMPERATURE (°C) PROPAGATION DELAY (t ) PD- vs. INPUT OVERDRIVE + INPUT OVERDRIVE (mV) MAX9118/MAX9120 PROPAGATION DELAY (t ) PD+ vs. PULLUP RESISTANCE 100 + + +1. 100 1000 10,000 R (kΩ) PULLUP PROPAGATION DELAY (t ) PD- vs ...
Page 8
SC70, 1.6V, Nanopower, Beyond-the-Rails Comparators With/Without Reference (V = +5V 0V 15pF OVERDRIVE MAX9117/MAX9119 PROPAGATION DELAY ( +5V) CC MAX9117-20 toc28 IN+ (50mV/div) OV OUT (2V/div) OV 20µs/div ...
Page 9
... N. Detailed Description The MAX9117/MAX9118 feature an on-board 1.252V ±1.75% reference, yet draw an ultra-low supply current of 600nA. The MAX9119/MAX9120 (without reference) consume just 350nA of supply current. All four devices are guaranteed to operate down to +1.6V. Their com- mon-mode input voltage range extends 200mV beyond-the-rails ...
Page 10
... SC70, 1.6V, Nanopower, Beyond-the-Rails Comparators With/Without Reference Reference (MAX9117/MAX9118) The internal reference in the MAX9117/MAX9118 has an output voltage of +1.252V with respect to V temperature coefficient is 100ppm/°C over the full -40°C to +85°C temperature range. The reference is a PNP emitter-follower driven by a 120nA current source (Figure 1). The output impedance of the voltage refer- ence is typically 200kΩ ...
Page 11
... V IN Figure 3. MAX9117/MAX9119 Additional Hysteresis = +5V, and if Additional Hysteresis (MAX9118/MAX9120) CC The MAX9118/MAX9120 have a 4mV internal hysteresis band. They have open-drain outputs and require an external pullup resistor (Figure 4). Additional hysteresis can be generated using positive feedback, but the for- ). For this HB mulas differ slightly from those of the MAX9117/ MAX9119 ...
Page 12
... V and the +5V supply voltage to the pullup resistor MAX9118 MAX9120 V REF Figure 4. MAX9118/MAX9120 Additional Hysteresis 12 ______________________________________________________________________________________ 2MΩ 2MΩ P-P 5V (3V) LOGIC IN 100mV R4 OUT Figure 5. Zero-Crossing Detector TRANSISTOR COUNT: 98 Typical Application Circuit +5V (+3V) +3V (+5V PULLUP ...
Page 13
... SC70, 1.6V, Nanopower, Beyond-the-Rails Comparators With/Without Reference (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) ______________________________________________________________________________________ Package Information PACKAGE OUTLINE, 5L SC70 1 21-0076 ...
Page 14
... Revision History Pages changed at Rev Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...