MAX917 Maxim, MAX917 Datasheet
MAX917
Available stocks
Related parts for MAX917
MAX917 Summary of contents
Page 1
... MAX919/MAX920 (with- out reference) require just 380nA of supply current. These features make the MAX917–MAX920 family of comparators ideal for all 2-cell battery applications, including monitoring/management. The unique design of the output stage limits supply-cur- rent surges while switching, virtually eliminating the supply glitches typical of many other comparators ...
Page 2
... +25° MIN MAX V = 1. +25°C MAX917 only 5V 8mA SOURCE MIN - +25°C MAX917 only 1.8V 1mA SOURCE MIN T = +25° 5V 8mA SINK MIN +25° 1.8V ...
Page 3
... SOT23, 1.8V, Nanopower, Beyond-the-Rails Comparators With/Without Reference ELECTRICAL CHARACTERISTICS—MAX917/MAX918 (continued +5V 0V IN+ REF A PARAMETER SYMBOL High-to-Low Propagation Delay t PD- (Note 4) Low-to-High Propagation Delay t PD+ (Note 4) Rise Time t RISE Fall Time t FALL Power-Up Time t ON Reference Voltage ...
Page 4
... Note 3: The hysteresis-related trip points are defined as the edges of the hysteresis band, measured with respect to the center of the band (i.e (Figure 2). OS Note 4: Specified with an input overdrive (V above and beyond the offset voltage and hysteresis of the comparator input. For the MAX917/MAX918, reference voltage error should also be added. 4 _______________________________________________________________________________________ CONDITIONS ...
Page 5
... TEMPERATURE (°C) MAX919/MAX920 SUPPLY CURRENT vs. OUTPUT TRANSITION FREQUENCY 1. 100 1k 10k 100k OUTPUT TRANSITION FREQUENCY (Hz) MAX917/MAX919 OUTPUT-VOLTAGE HIGH vs. SOURCE CURRENT 0 1. 0.4 0.3 0.2 0 SOURCE CURRENT (mA) 5 ...
Page 6
... SHORT-CIRCUIT SOURCE CURRENT vs. TEMPERATURE 140 120 100 1. -40 - TEMPERATURE (°C) MAX917/MAX918 REFERENCE VOLTAGE vs. TEMPERATURE 1.246 1.245 1.244 V = 1.8V CC 1.243 1.242 1.241 -40 - TEMPERATURE (°C) MAX917/MAX918 REFERENCE OUTPUT VOLTAGE vs. ...
Page 7
... PROPAGATION DELAY (t vs. INPUT OVERDRIVE 100 INPUT OVERDRIVE (mV) ) vs. PROPAGATION DELAY ( 5V) CC 10k 20μs/div ) PD 1. 100 1000 ) PD 1. PD- MAX917-920 toc27 IN+ (50mV/ div) OUT (2V/div) 7 ...
Page 8
... PD 1.8V) CC MAX917-920 toc32 20μs/div = 5V) MAX917-920 toc34 IN+ (50mV/div) OUT (2V/div) MAX917/MAX919 PROPAGATION DELAY ( 3V) CC MAX917-920 toc30 IN+ (50mV/ div) OUT (2V/div) 20μs/div MAX917/MAX919 10kHz RESPONSE (V = 1.8V) CC MAX917-920 toc33 IN+ (50mV/ div) OUT (1V/div) 20μs/div POWER-UP/DOWN RESPONSE MAX917-920 toc35 ...
Page 9
... Large internal output drivers allow rail-to-rail output swing with up to ±8mA loads. The output stage employs a unique design that mini- mizes supply-current surges while switching, virtually eliminating the supply glitches typical of many other comparators. The MAX917/MAX919 have a push-pull _______________________________________________________________________________________ IN+ OUT IN- ...
Page 10
... MAX406. Applications Information Low-Voltage, Low-Power Operation The MAX917–MAX920 are ideally suited for use with most battery-powered systems. Table 1 lists a variety of battery types, capacities, and approximate operating times for the MAX917–MAX920, assuming nominal conditions. ...
Page 11
... They have open-drain outputs and require an external pullup resistor (Figure 4). Additional hysteresis = 5V, and can be generated using positive feedback, but the for- mulas differ slightly from those of the MAX917/ MAX919. Use the following procedure to calculate resistor values. ). For this HB 1) Select R3 according to the formulas the two resulting resistor values ...
Page 12
... Figure 4. MAX918/MAX920 Additional Hysteresis Pin Configurations (continued) TOP VIEW N.C. 1 IN- (REF) 2 MAX917 MAX918 3 IN+ MAX919 MAX920 ARE FOR MAX917/MAX918. 12 ______________________________________________________________________________________ Figure 5 shows a zero-crossing detector application. ⎛ ⎞ ⎜ ⎟ The MAX919’s inverting input is connected to ground, ⎝ ⎠ R1 ...
Page 13
... Comparators With/Without Reference For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 14
... Comparators With/Without Reference For the latest package outline information and land patterns www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status ...
Page 15
... Added lead-free and automotive qualified parts Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 15 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...