MAX922 Maxim, MAX922 Datasheet - Page 2

• Manufacturer Part Number: MAX922
• Description: The MAX921–MAX924 single, dual, and quad micropower, low-voltage comparators feature the lowest power consumption available
• Manufacturer: Maxim

Ultra Low-Power,
Single/Dual-Supply Comparators
ABSOLUTE MAXIMUM RATINGS
V+ to V-, V+ to GND, GND to V-................................-0.3V, +12V
Inputs
Outputs
ELECTRICAL CHARACTERISTICS: 5V OPERATION
(V+ = 5V, V- = GND = 0V, T
Stresses beyond those listed under “Absolute Maximum Ratings‘” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
2
Supply Voltage Range
Supply Current
Input Offset Voltage
Input Leakage Current (IN-, IN+)
Input Leakage Current (HYST)
Input Common-Mode Voltage Range
Common-Mode Rejection Ratio
Power-Supply Rejection Ratio
Voltage Noise
Hysteresis Input Voltage Range
Response Time
POWER REQUIREMENTS
COMPARATOR
Current, IN_+, IN_-, HYST...............................................20mA
Voltage, IN_+, IN_-, HYST................(V+ + 0.3V) to (V- – 0.3V)
Current, REF....................................................................20mA
Current, OUT_ .................................................................50mA
Voltage, REF ....................................(V+ + 0.3V) to (V- – 0.3V)
Voltage, OUT_ (MAX921/924) .....(V+ + 0.3V) to (GND – 0.3V)
Voltage OUT_ (MAX922/923)...........(V+ + 0.3V) to (V- – 0.3V)
OUT_ Short-Circuit Duration (V+ ≤ 5.5V) ...............Continuous
_______________________________________________________________________________________
PARAMETER
A
= T
MIN
to T
MAX
IN+ = IN- + 100mV
(Note 1)
V
IN+ = IN- = 2.5V
MAX921, MAX923
V- to (V+ – 1.3V)
V+ = 2.5V to 11V
100Hz to 100kHz
MAX921, MAX923
T
A
CM
= +25°C, 100pF load
, unless otherwise noted.)
= 2.5V
CONDITIONS
MAX921,
HYST = REF
MAX922
MAX923,
HYST = REF
MAX924
Continuous Power Dissipation (T
Operating Temperature Ranges:
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
8-Pin Plastic DIP (derate 9.09mW/°C above +70°C) ...727mW
8-Pin SO (derate 5.88mW/°C above +70°C)................471mW
8-Pin µMAX (derate 4.1mW/°C above +70°C) .............330mW
8-Pin CERDIP (derate 8.00mW/°C above +70°C)........640mW
16-Pin Plastic DIP (derate 10.53mW/°C above +70°C)..842mW
16-Pin SO (derate 8.70mW/°C above +70°C) ................696mW
16-Pin CERDIP (derate 10.00mW/°C above +70°C) ......800mW
MAX92_C_ _ .......................................................0°C to +70°C
MAX92_E_ _.....................................................-40°C to +85°C
MAX92_MJ_ ..................................................-55°C to +125°C
T
C/E temp. ranges
M temp. range
T
C/E temp. ranges
M temp. range
T
C/E temp. ranges
M temp. range
T
C/E temp. ranges
M temp. range
C/E temp. ranges
M temp. range
Overdrive = 10mV
Overdrive = 100mV
A
A
A
A
= +25°C
= +25°C
= +25°C
= +25°C
REF- 0.05V
MIN
2.5
V-
A
= +70°C)
±0.01
±0.02
TYP
2.5
2.5
3.1
5.5
0.1
0.1
20
12
4
V+ – 1.3
MAX
REF
±10
±40
3.2
3.2
4.5
7.5
6.5
8.5
1.0
1.0
11
11
±5
4
5
4
5
6
UNITS
µV
mV/V
mV/V
mV
µA
nA
nA
µs
RMS
V
V
V